June 20, 2023 to June 24, 2023 – The Pyramid Marriott, Albuquerque, New Mexico You can follow the QR Code Link in the attached flier for the 2023 Grand National in Albuquerque or follow this link to book your room now: https://qr.io/r/ky5vx6 2023 CADILLAC & LASALL… Organized by CLC New Mexico Region | Type: clc, grand, national
Adam T Laws Online
Sean O'Hare Online
Started by Ray in 1963/64 Cadillac Specific Discussion. Last reply by Ray 3 minutes ago. 10 Replies 0 Likes
I've bounced around here on the forum. Has anyone used the retro kit by Auto A/C Solutions out of Texas ? Any thoughts ? Continue
Started by Tim Broyan in Restoration Discussion. Last reply by Tim Broyan 2 hours ago. 2 Replies 0 Likes
I've replaced-repaired, cleaned and tested the complete system so I'm confident that everything will work as new. I vacuum tested the system first to see first if the installed system had any leaks.…Continue
Started by Peter Greenway in 1963/64 Cadillac Specific Discussion. Last reply by Peter Greenway 10 hours ago. 3 Replies 0 Likes
Hello, I have a 63 4-door sedan and want to replace all the seat covers on the front bench and rear seats. Can anyone recommend the best place to buy the complete seat kits (already stitched up)…Continue
Started by Roy in 1963/64 Cadillac Specific Discussion. Last reply by Lee Martin 12 hours ago. 10 Replies 0 Likes
I have a bad window motor in the passenger side door. I have removed the door panel and am at a complete loss as to where to start and what to do from here. Does anyone have any step by step…Continue
Posted by Curtis Dover on January 2, 2023 at 5:23pm 0 Comments 0 Likes
Hey guys, I need some help. Could someone send me some pictures on how the first hood release lever on a factory 1964 Cadillac is set up, where it comes though the grille. Not the secondary one. I need to know where the thumb or finger position is located through the grille. Is it above or below the center grille molding piece? Mine seems to be positioned behind the center molding piece and will not adjust above or below the molding. I have a wire tied to it to release it…
ContinuePosted by Ray Schick on October 30, 2022 at 4:34pm 4 Comments 0 Likes
I removed the front cover to change out the timing chain & gears all that went pretty well when I put the cover back on I put in a fresh oil filter ,filled it up figured it would be enough to prime the oil pump when I started the car .Fired up the car and heard lifters rattling, So I shut the car down right away. So I removed the oil filter housing, and poured oil down the neck of the oil pump housing filled it up and filled up the filter put it all together and fired it up and same…
ContinuePosted by Thomas Reichenberger on October 13, 2022 at 11:47pm 0 Comments 0 Likes
Caddy members, I’m upgrading my 64 2-door coupe deville.
motor guy lost my block (machine shop went under) so I’m replacing motor & tranny with LS conversion. I have motor parts (other than block) for 429, rebuilt transmission, converter, and too many other motor parts not needed with fully dressed LS going in.
Email me (Tom.reichenberger@ipsper.com) or call me (210-739-4854) if you’re interested…..I live in San Antonio, TX.
thanks, TX…
ContinuePosted by Chris Anderson on September 13, 2022 at 7:14pm 7 Comments 0 Likes
While working on my trunk lock on 64 Cadillac, I mistakenly closed the locking mechanism while the trunk was open. Is there an easy way to manually release the lock back to the open position?
Thanks.
© 2023 Created by Jason Edge.
Powered by