Crank shaft bolt
I'm working on the front of the engine on my "63. Does anyone know the correct thread size of the internal treads on the crank shaft? I'd like to go into the hardware store and buy a longer bolt to use in installing the harmonic balancer and am considering securing it with a shorter bolt and washer after it's installed.
Replies to This Discussion
-
Permalink Reply by Chris McBride on
-
most people do not have those laying around and most home improvement and auto parts stores do not stock them. The actual bolt is 9/16" - 18 x 1 5/8" long...with a very thick large washer. This turns out to be the same bolt size used on the large front bumper end to frame brackets and I literally have buckets of them if you need one. I use a couple of the large washers behind it to firmly press against the balancer. You can also get these bolts new from places like boltdepot.com but once I figured out the bumper end bolts are the same I quit keeping them in stock. If you need one of these bolts I can set you up with a bolt and 2 washers for $10 + s/h. …Added by Jason Edge at 10:04pm on September 17, 2018
hth
Chris
Members
Forum
Website Header - Experimenting with Rotating Member Cars
Started by Jason Edge in General Discussion. Last reply by Jason Edge yesterday. 6 Replies 2 Likes
I was thinking or rotating member 63's and 64's up in the header and used Mark Geertsma's 1963 Sedan de Ville as a test car. It gets a little grainy making the picture that small, but not too bad.…Continue
My Only Eldorado Parts Car - A 1963 Picked up in 2001
Started by Jason Edge in General Discussion. Last reply by Jason Edge on Monday. 2 Replies 0 Likes
I was thumbing thru parts car folders and run across the 63 Eldorado I parted out way back in 2006 and saw the dirty but good condition body tag. I like to clean them up I guess as a token and of…Continue
Anybody in Reno or Lake Tahoe area?
Started by Mack in 1963/64 Cadillac Specific Discussion on Sunday. 0 Replies 0 Likes
We have a group of Cadillac guys in Reno/Tahoe area and we will be cruising and participating in the local car shows this season!let me know if you’re in the area and wanting to join in.happy…Continue
Adapt, Improvise and Move an Cadillac Engine!
Started by Jason Edge in General Discussion. Last reply by Jason Edge on Friday. 3 Replies 0 Likes
Just wanted to pop in and say hello and give a quick update on a couple of things and share a garage thing I thought you might get a kick out of. First, my arm is out of the brace as of last Monday…Continue
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
