Crank shaft bolt
I'm working on the front of the engine on my "63. Does anyone know the correct thread size of the internal treads on the crank shaft? I'd like to go into the hardware store and buy a longer bolt to use in installing the harmonic balancer and am considering securing it with a shorter bolt and washer after it's installed.
Replies to This Discussion
-
Permalink Reply by Chris McBride on
-
most people do not have those laying around and most home improvement and auto parts stores do not stock them. The actual bolt is 9/16" - 18 x 1 5/8" long...with a very thick large washer. This turns out to be the same bolt size used on the large front bumper end to frame brackets and I literally have buckets of them if you need one. I use a couple of the large washers behind it to firmly press against the balancer. You can also get these bolts new from places like boltdepot.com but once I figured out the bumper end bolts are the same I quit keeping them in stock. If you need one of these bolts I can set you up with a bolt and 2 washers for $10 + s/h. …Added by Jason Edge at 10:04pm on September 17, 2018
hth
Chris
Members
Forum
front seat crest
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch 9 hours ago. 3 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
Future of CLC Judging
Started by Jason Edge in Restoration Discussion. Last reply by Bill Wolf 20 hours ago. 3 Replies 0 Likes
First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system. The old system was very good, however, I believe what Bill and the…Continue
Coolant Overflow Bottle / Reservoir for 64 Cadillac Eldorado
Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf 20 hours ago. 7 Replies 0 Likes
Greetings Everyone. I read a discussion thread about "radiator and related", covering coolant overflow. Has anyone fitted an overflow reservoir / bottle to their 64 Cadillac? Is there if a…Continue
Dino Radiator Leak - Time to Recore!
Started by Jason Edge in General Discussion. Last reply by Bill Wolf on Friday. 36 Replies 0 Likes
I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
