Tune up
What is Points gap supposed to be
Dewell angle
Thanks
Replies to This Discussion
-
Permalink Reply by Dennis P. DiBari on
-
Hi Joe,
The dwell angle is usually set from 28 to 30 degrees. Pretty sure that is equivalent to .016 with a flat gauge by hand. Just make sure your dwell gauge is still accurate - mine was not. If the points and condenser are not one piece, you can get the flat gauge in there with the points on the HIGH spot of the cam.
Dennis DiBari, Cottekill, NY
-
Permalink Reply by Joseph Innamorato on
-
Good morning
Thank you
yes it separate
Agreed the one I had was old one from Sears
Haven’t used it in 35 years
Found it in my mothers basement where I had some oils tools
Have a great day
-
-
You're welcome, Joe. Use the flat gauge to be sure (.016) it is accurate. I picked up a used Dwell meter on Ebay and had it checked with my friend's to be sure. Talk soon.
Dennis DiBari
-
-
Dennis
Thanks got another meter
All set car running great
Have a good afternoon
-
-
Joe,
GREAT work!! Talk to you soon at the Zoom meeting.
Dennis DiBari
-
-
Yes
see you on zoomthanks again
Photos
Members
Forum
Fuel pump brass fitting
Started by Mark Mata in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 10 minutes ago. 1 Reply 0 Likes
Hello everyone, I was wondering if anyone has a part # for the brass fitting exiting out of the fuel pump up to the glass fuel bowl. I looked for a previous discussion here on the site but couldn't…Continue
63 & 64 Eldorados at Mecum Auction in Kissimmee
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari 5 hours ago. 1 Reply 0 Likes
Here is a 1963 & 1964 Eldorado I saw at Mecum auction in Kissimmee, Florida today. This was today’s main activity as part of the 2026 CLC Winter Reunion in Orlando. There are over 4,200 event at…Continue
64’ A/C Power Servo - Vacuum Actuator
Started by Jacob Foster in 1963/64 Cadillac Specific Discussion. Last reply by Bernie Long Jan 1. 1 Reply 0 Likes
Gents, good morning!I’m looking for advice on how to fix the A/C Power Servo on my 1964 Cadillac Deville. The unit itself seems to be working correctly, but the vacuum actuator is leaking off. Has…Continue
CLASSIC CADILLAC PARTS CLOSED JAN 5-11, 2026
Started by Jason Edge in For Sale Jan 1. 0 Replies 0 Likes
Hello All,HAPPY NEW YEAR!Just a heads up that I will be in…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
-
January 18, 2025 - 63/64 Cadillac Chapter Zoom Meet-Up
January 18, 2026 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes
© 2026 Created by Jason Edge.
Powered by
