I need some help/advice guys and gals! The short story: I purchased my '64 deVille in 2011 from dealer in Utah. Drove it home with a couple of minor issues to Virginia. Started working on headlight switch, undr dash pad vacuum tubing, etc. Due to work schedule, etc, I let the car sit until this year - I know, I've beat myself up enough.
Going through anything that may give me trouble (hoses, cap/rotor/points/condenser, belts ...) on the 2,200 mi trip home to Montana. I just replaced my pts/condenser, found my vacuum advance is bad (ordered one), and was starting to swap the plug wires onto the new cap when placement of #1 didn't look right. Firing order is 18726543, and the workshop manual's picture of the cap with wire numbers marked shows #1 between screw and window, and #8 next, at the corner of the window, CW. The way it was wired is #1 is CCW two positions. The firing order is correct and the car ran well back then.
Am I nuts or did the rebuild mechanics get the distributor in wrong and made up for it by clocking the wires to get it to run? The shop manual that came with the car is marked with highlights, stars and question marks, leading me to think this may have been their first rebuild.
I'm new at posting, will try to add photos. Thanks in advance for any help,
Linda
Tags:
Hi Linda,
Your comments are the best. I would pop in the new check valve and the new 11/32 hose for the booster - can't hurt. You're right; the parts stores don't carry that special hose - thought I was from Mars! Now that your advance is in, you should be good to go. Thanks for the compliment on my Caddy. Safe trip back to Big Sky Country. Take your time.
Dennis
Thanks Dennis, I'll install the new check valve and grommet (if it fits), the hose is new - I meant to say 11/32", so good to go there. OPGI can get the Bendix booster rebuild kit, but hope mine is good enough to get me home.
Thanks for the advice and conversation, not many people I know like to talk old cars. Best wishes,
Linda
OK Linda,
Good trip and we'll talk soon!! You are very welcome.
Dennis
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by CHRIS CARLSON yesterday. 1 Reply 0 Likes
Hey everyone, I need to replace my transmission input seal before spring starts, I’ve been losing a lot of fluid post Sunday drive. I figured I’d do the rear main seal service bulletin at the same…Continue
Started by Michael Monson in Wanted to Buy. Last reply by Michael Monson on Thursday. 2 Replies 0 Likes
Looking for a heater control valve 9.795 for my 1964 Deville. ThanksContinue
Started by Jeff Donaldson in General Discussion. Last reply by Logan Robb on Tuesday. 4 Replies 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kurt Feb 22. 7 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2026 Created by Jason Edge.
Powered by