Anybody out there have any experience or direction how to remove and replace the chrome trim moulding around the front door window glass? Kevin
Tags:
Kevin, the window has t come out. If its a 63, lucky U. 2 screws hold the bar in place. The rollers on the regulator ride in the bar, on the bottom of the window channel
2 screws on the back of the top chrome L shaped piece, hold it to the channel.
I got it replaced. Thanks Russ. Kevin
Kevin, is your window already out of the car? If not follow shop manual to remove glass. Then remove screws that hold the side & top trim to the lower channel assembly and gently pry the trim away from glass. When reinstalling I have used a lot of WD 40 to get the window back wedged into the seal and trim and lower channel.
Thanks Jason. It worked!!!! Got it. Kevin
so u have to take the front window out in order to remove front window trim??? im in process of trying to remove trim or trying figure it out .but dont wanna take that Big window out
Looking at picture below for front window trim with read arrows pointing to left and right roof panel trim, and green arrows pointing to 5 pc reveal trim:
--> left, top and right reveal trim next to glass (green arrows) - removes with reveal removal tool. (windshield does not have to be removed)
--> bottom left and right reveal trim behind cowl (bottom green arrows) - cowl has tom come off to access 5/16" screws that hold lower reveal brackets in place. (windshield does not have to be removed)
--> left and right front roof panel trim (red arrows) - WINDSHIELD AS TO COME UP TO ACCESS TRIM SCREWS). The removal of this trim indicating removal of windshield is in the Shop manual (page 16-80 in 1963 manual; page 16-85 1964 manual),
Once you remove the windshield and rubber seal you will then have access to a series of screws that holds the left and right front roof panel trim in place as seen below:
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Jacob Simmons 23 hours ago. 13 Replies 0 Likes
As is with my luck with this car (I still love it to pieces, just needs some TLC from neglect and not being driven) I’ve developed another issue. A small coolant leak has started from the Passenger…Continue
Started by Bill Wolf in General Discussion. Last reply by Dennis P. DiBari on Tuesday. 6 Replies 0 Likes
I am trying to replace the front wheel cylinders on my 63 SDV and can't figure out how to get a wrench on the bolts holding them on. Does the backing plate have to come off and if so, how? Thank you…Continue
Started by Anthony Vanacore in For Sale. Last reply by Anthony Vanacore May 6. 5 Replies 0 Likes
Hello,My father and I are restoring our 63 series 62 conv, we had the chrome bezels for the window/seat switches rechromed. During this process we also installed factory power door locks to the…Continue
Started by Jason Edge in General Discussion May 3. 0 Replies 0 Likes
As I was documenting the non-AC 63 Eldorado parts car I bought in a couple months ago, the solid panel dash end panels intrigued me and thought I would share a couple of pictures and thoughts. First,…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
May 17, 2026 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2026 Created by Jason Edge.
Powered by