All Discussions Tagged 'National' (5)
| Discussions | Replies | Latest Activity |
|---|---|---|
CLC 2019 Grand National - Louisville, Kentucky, June 11-15, 20191963/64 Cadillac Chapter 2019 Grand National Page www.2019GN.6364Cadillac.com Host Hotel: The Crown Plaza Louisville 830 Phillips Ln,… Started by Jason Edge |
35 |
Jun 19 Reply by Marty Smith |
1963/64 Cadillac Chapter July 2018 Newsletter PostedI have just completed and posted the July 2018, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadilla… Started by Jason Edge |
3 |
Jul 3, 2018 Reply by Jason Edge |
CLC 2018 Grand National - San Marcos, Texas, June 5-9Host Hotel: Embassy Suites by Hilton San Marcos 1001 E. McCarty Lane, San Marcos, TX 78666, 512-392-6450 Backup Hotel: Courtyard by Ma… Started by Jason Edge |
13 |
Jun 20, 2018 Reply by Jason Edge |
Driving to the CLC Grand National in San Marcos, TX.Hi all, Picked up the Caddy on May 29th in Miami and drove to Ocala, FL to visit a good friend who used to live in Curaçao. Have taken the… Started by Clifford Muskus |
10 |
Jun 4, 2018 Reply by Kevin Campbell |
Ramping Up for Texas!Kinda crazy that I will be in Texas 1 week from now watching the Cadillacs & LaSalles roll in as part of the 2018 CLC Grand National. I… Started by Jason Edge |
0 | May 30, 2018 |
Photos
Members
Forum
A Drilling No-No .... That Worked!
Started by Jason Edge in General Discussion. Last reply by Jason Edge 1 hour ago. 16 Replies 0 Likes
Thought I would share a quick story regarding something I did that I generally do not recommend - Free handed drilling a broken front engine cover bolt. Before I jump into it I will say I do not…Continue
Exhaust manifold: Repair, replace or headers?
Started by Dutch Dickinsen in General Discussion. Last reply by Tony and Ginny 429 6 hours ago. 1 Reply 0 Likes
My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold.It looks like my options are limited to rolling the dice on a used manifold, converting to headers or seeing if…Continue
Steering Wheel
Started by Mark Borer in General Discussion 11 hours ago. 0 Replies 0 Likes
plz watch this videoIt shows play between the 2 cylinders that make up my columni have tightened everything up as best as I can....but it moves a bitthe lower cover had a screw that lined it up, and…Continue
Help! I need a 1964 Eldorado front left fender.
Started by Jorge M in Wanted to Buy. Last reply by Jon Ettman 13 hours ago. 5 Replies 0 Likes
Help looking for a 1964 Eldorado front fender for a convertible.Thank you please contact djjmoreno84@gmail.comContinue
Blog Posts
Starter Solenoid replacement-how difficult? Where to buy?
Posted by Norman Silverman on August 20, 2019 at 8:24pm 6 Comments 0 Likes
Hello All.
I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …
ContinueFrame Markings
Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment 0 Likes
Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…
Lining up the drive shaft
Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments 0 Likes
Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.
Thanks
Dominic
Upper A Arm Rubber Bumpers
Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments 1 Like
I have found a very good replacement part for the Upper A Arm Bumpers. The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were. The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer. Part number is on the box in the photos. First photo is the box next to the box is the S10 part and an original. Next photo shows my sanded down part next to an original.…
ContinueEvents
© 2019 Created by Jason Edge.
Powered by
