As most of you know I just brought in almost 400 lb of Cadmium plated bolts, etc. Cheryl, my boss and Cadillac Parts Apprentice indicated she needed some help when looking at the 1st batch of about 175 lbs of smaller bolts, I threw out across our 12 ft table. WELL, I GOT HER SOME HELP!  See 2nd picture. As Tony would say, enjoy!  Hope you are all having a good Saturday!

Facebook Facebook

Views: 104

Reply to This

Replies to This Discussion

Ok, All. I think my CPA (Cadillac Parts Apprentice) is going to be the first "associate" in Classic Cadillac Parts history to go straight from
Apprentice, to CPM (Master), completely leapfrogging over her tenure as Journeyman. She is a bolt & nut sorting Wizard of unimaginable power. Her Sort & Orginize Midichlorian Count is literally OFF THE CHARTS! Not only that, she is coming up with deep philisophical stuff. As I was watching her work she gazed across the expanse of thousands of bolts and blurted out "THEY ARE TRUE TO WHAT THEY ARE!". Is that deep or what?! Finally, to bring her up to full Master Level, I presented her with her own bolt measuring tool. In an add way she seemed to find pleasure in sticking the bolts through the little holes. And, I will just leave it at that!

RSS

Photos

  • Add Photos
  • View All

Forum

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 14 hours ago. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb yesterday. 11 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 6 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service