My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?
Tags:
Jason, are the wooden blocks a factory component? Mine also came with the black wood block for the tire block.
It is mega hot here this week. Perhaps repainting my bumper jack is something easy I can accomplish this week......
I believe all Cadillacs of the 60s and 70s came with those black-painted triangular blocks of pine. They did in my 67, 69, and 70 cars. I plan to take the dimensions off those and prepare a block for this 1964 car which is missing the block.
Did they come with one or two wedge blocks ?
One block in each of my cars - except the 64.
63's and 64's had one block.
Thatd be great! I think I have mine kicking around here somewhere. Let me know what the dimensions of yours is. I think mine was split in two it was so dry. Id like to remake mine as well.
Measurements of the block in the trunk of my 69 Cadillac:
Picture a right triangle:
Base = 3 1/2"
Height = 5 3/4"
Hypotenuse = 6 5/8"
The block is 3 1/2" thick, so if looking down on the base, you'd see a 3.5" square.
The block in my 67 Cadillac also is made of pine painted black, but the dimensions are a fraction of an inch different.
This is excellent! Thank you!
I shall remake mine as well
It looks great, but the animated picture is spectacular. The talent in this group is impressive.
Thanks for the picture. I will investigate.
Travis J. Hensley Online
Started by Kevin Robles in 1963/64 Cadillac Specific Discussion. Last reply by Kevin Robles 43 minutes ago. 3 Replies 0 Likes
does anyone out there have any experience with seat foam replacement on a 63/64 Cadillac. I had my seats reupolstered many years ago in original leather/fabric and they still look great, but the…Continue
Started by tim sparks in General Discussion 6 hours ago. 0 Replies 0 Likes
anybody have an xtra stainless steel shim for 1963 carter afb carb. thank youContinue
Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 14 hours ago. 1 Reply 0 Likes
Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue
Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark 22 hours ago. 13 Replies 0 Likes
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by