Headed out for drive. Oil pressure good tempnat one quarter on gauge, went about 1.2 miles looked bl at oil pressure it was at ZERO! I hv mech gauge, so i thumped it didnt budge, immediately pulled over and shut down. Didnt hear any noies or smell anything. Opened hood, oil splattered all over engine bay from about oil filter back on passenger side. Hadno lights or tools and bay was a mess s so i couldnt assess anything as to origin.
Well i started up the road for the 2 mile walk to house and saw the oil trail. As you can see, pretty significant. Something clearly went boom. The oil trail is about one quartr mile long. I can see were it started . Initially looks like from were oil is most concentrated on engine, its around the oil pump or filter. Any idea what could cause such a blowout ? I hope i caufht it soon enough to shut down.
Tags:
I hv used the anearobic on the rear gasket seal. I didnt use any sealant or other wise on the cork gasket i put in. Cked today, no seepage, . I guess as tony mentioned was the pressure aspect. Will cork hold up?. Last one i took out held for several years as thats when i got it and i hvnt changed it
I don't think cork is used in those areas. Too much pressure and liquid right there. Cork is generally used in areas like the oil pan and valve covers where there isn't a lot of pressure directly against the gasket.
Per advice, removed the cork gasket, which was holding, found 1/32 paper, which was thicker than the kit supplied gasket from felpro. cut out to shape,,,, put it in car, and again, it will not hold. but the thick cork does. so I am in search of a thick paper gasket, probably 1/8,, i have searched google with no discernible result.
I will note however, since the first removal, i noted the bolt that goes into the engine doesnt seem to want to tighten. it tightens, but not to the 15 like the bolt that is not into the block,, could the threads be worn,,it may be why they used the thick cork in the first place that went out because it could seal without the torque if that is that case, what wold be remedy from there. i read a bout that helicoil repair, but dont want to go there unless last resort, so if anyone has a suggestion from hear, I'm all ears.
The only logical repair is a heli coil. If you drill it out and tap it to a larger size you will have to drill a larger clearance hole in the part you are trying to mount which weakens it. The down side to heli coil repair kit is they are a bit pricey but do come with the required drill and tap plus heli coils and installation tool. It really is the proper repair. If you can't get your regular drill into position, you might need to get a close quarter drill like this...
https://www.amazon.ca/Genesis-GCQD38A-8-Inch-Close-Quarter/dp/B00CD...
That's a Canadian price so look one up at a US location. All told doing this repair right and yourself should be fairly easy and would save you the grief of having to cobble something up over and over. The money spent on the heli coil kit is small potatoes compared to the cost of having a shop do it unless you have a really reasonable mechanic available.
Question on the hole bored into the block
Im guessung this hole is a dead end hole and doesnt empty into block or cylinders. Is that correct. I intend on blowing out the shavings, but if something is left behind,
Picture of the stripped hole would help out. I use heli coils all the time, no big deal. You can drill and tap the hole for the original sized bolt. Again, I do it all the time on thermostat covers, water pump bolts into the front engine cover, aluminum intakes.
Repair the hole and use a stock gasket.
Started by Jeff Donaldson in General Discussion. Last reply by Marty Smith 20 hours ago. 2 Replies 0 Likes
Has anyone bought new oem headlights from Lectric Limited? They want $150 for a set of new remanufactured ones. Any advice would be appreciated.JeffContinue
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 5 Replies 0 Likes
Hey everyone. Last year I had some trouble keeping the Caddy running. A little backstory, car hadn’t ran in 30 years. Rebuilt the crankshaft. I had it running pretty well for a bit. Even drove it the…Continue
Started by Doug Scarrow in For Sale yesterday. 0 Replies 0 Likes
Just listed very good 8619952 Cadillac front pump complete. $160 plus shipping https://www.ebay.com/itm/266805513612Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by