Controlled Differential Decal
Does anyone have a pic of where the approximate location should be for the differential decal inside the trunk ? There is a pic In one of Jason's posts but it is a close up and not too definitive Thanks !
Replies to This Discussion
-
Permalink Reply by Tony and Ginny 429 on
-
You will have a tag on the differencial ( ham ) ,under the car
Do not think there is anything in the trunk ,myself
-
Permalink Reply by Jason Edge on
-
Marty I added better pictures on the Rear End/Differential thread at this link: http://6364cadillac.ning.com/profiles/blogs/differentials
Note, That I have pictures of 3 1964's with the Controlled and they are in the same location as posted in the link and on my car. I did find a 63 with limited slip and it was in the same relative location, but on the left side, so perhaps 63's was on the LH side. I know even on the 64's they are in the same relative spot but have seen them up or down an inch or two. Either way no one would knock any points off at GN judging regardless or side. I will dig around my parts car pictures some more.
-
Permalink Reply by Marty Smith on
-
Thanks Jason , I wasn't that concerned abut the judging points I was more concerned of you seeing it in the wrong place and asking why I didn't ask you where it went : ).
Photos
Members
Forum
63 Hydra-Matic won't shift out of first
Started by Norm Waters in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 3 hours ago. 3 Replies 0 Likes
Hello everyone. I had a perfectly good shifting Hydra-Matic transmission until I elected to fix the leak at the dip stick tube. I just did a quick seal with gasket maker since my current tube is…Continue
Rear brake lock up when cold
Started by Cliff Johnston in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 3 hours ago. 1 Reply 0 Likes
Hi everyone, ever since getting the car back on the road, the rear brakes grab when they are cold and I’m moving at slow speed. Once I get along the road and stop they are fine. I see some posts…Continue
2 timing covers. 63 390. One crossover pipe ac, harmonic balancer
Started by Kim K Kaiser in For Sale. Last reply by Kim K Kaiser 4 hours ago. 2 Replies 0 Likes
Vacuum advance
Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Thomas Yarri 15 hours ago. 4 Replies 0 Likes
Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue
Blog Posts
1963 series 62 convertible transmission issue
Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment 0 Likes
Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…
ContinueNew vehicle in the club
Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment 0 Likes
I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha. …
Torque converter grab when idling in Drive
Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments 0 Likes
Hi Everyone, been quite a while since i have been on here.
I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.
With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.
I've had the car dyno tuned and…
ContinueCan you help? Driveshaft Question....
Posted by Chris on May 30, 2021 at 8:55am 1 Comment 0 Likes
Hello!
Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…
ContinueEvents
© 2021 Created by Jason Edge.
Powered by
