Steering Column Shifter
1964 Conv. non-tilt. Got in my car today and went to put my shifter in "Reverse, or Drive " and the shifter moved but did not go into gear. I looked in the engine compartment and my shifter rod from the steering column WAS NOT moving to change position. Can anyone advise what to do next?
Thank you
Dominic
Replies to This Discussion
-
Permalink Reply by Jason Edge on
-
On the non tilt columns, looking at your shop manual illustration, shift lever connects to shifter tube that connects to the shifter lever. It is a direct connection and all rotate together and I have outlined in yellow in illustration.
The carrier is pressed onto the shifter tube, onto a keyed area that keeps the carrier locked in place. It sounds like you carrier was not pressed onto the shifter tube all the way or has worked it self up and off the tube over the years. See the keyed area pointed to by pen in 2nd picture.
Members
-
Travis J. Hensley Online
-
-
Forum
Gump(Pat Westphal) you’re a gosh darn genius!
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal yesterday. 2 Replies 0 Likes
So I have been having problems with my brake lights. At first I thought it was both sides and turns out it is only the drivers side. Also, I thought the blinker worked and it didn’t and turned out…Continue
Front grill
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 11 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Steering slack/play
Started by Nile Bolen in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 4 Replies 0 Likes
I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack. Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings,…Continue
Add cruise control/Aftermarket Cruise control
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler on Monday. 12 Replies 0 Likes
Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
