1964 Heater Core Replacement Question-Non AC
Just a quick question about the Heater Assembly. I have been following the manual, but still have a question. I have the glove box removed, the bowden cables taken off, and the section under the hood removed. I am having difficulty in seeing where the Heater assembly is attached. Once this is taken down, I will have access to the old core. Any info or pics on this would be much appreciated.
Comment
-
Comment by David Cotton on May 10, 2015 at 9:19pm
-
Good advice, thank you.
-
-
Thanks for your input. Very helpful.
-
-
Thanks very much.
-
Comment by Jason Edge on May 10, 2015 at 6:00pm
-
Perhaps the above picture may be helpful..maybe not, or some of the others in our AC/Heat Photo album linked to from our Help Page. I will try to find some better heat only pictures and post. I have changed out my heater core on my 64 CDV with AC/Heat Comfort control some 10+ years ago but it has the evaporator to the right so is a bit different. When I part a car out the entire dash is out of the car and front clip is off the car so I literally just walk up to it and unbolt it.
I would suggest checking out John Serfling's article in our Sept 2012 Newsletter where describes (quite humorously at times) his adventure with his heater core change out. Click Here for the link.
Members
Forum
Adapt, Improvise and Move an Cadillac Engine!
Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari 18 hours ago. 1 Reply 0 Likes
Just wanted to pop in and say hello and give a quick update on a couple of things and share a garage thing I thought you might get a kick out of. First, my arm is out of the brace as of last Monday…Continue
Front Fender Skirt Backing Bracket Access – Question + Cad Plate Love
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Tuesday. 1 Reply 0 Likes
Hello all,I’m in the middle of swapping out the front fender skirt backing brackets on my ’64 Fleetwood and had a quick question for the group. I picked up a beautiful fresh set of cadmium plated…Continue
Power Booster Install
Started by Rob Spring in 1963/64 Cadillac Specific Discussion. Last reply by Rob Spring Apr 8. 9 Replies 0 Likes
Hey! I’ve seen the 63/64 power booster and master cylinder combination has been covered very clearly. I’m in the process of replacing mine. I was hoping someone could give me insight on a specific…Continue
1964 Cadillac Deville Neutral Safety switch and Oil Filter Housing Assembly
Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin Apr 7. 3 Replies 1 Like
Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering. Also, possibly looking for an oil filter housing assembly for a 1964 429 motor. Starting to get…Continue
Blog Posts
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 13 Comments 0 Likes
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2025 Created by Jason Edge.
Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website