63/64 Cadillac Website

Tail light lens question.

Good morning, Can someone tell me if I am missing something. I have removed four screws to change burned out bulbs in the back of my 64 SDV, but the plastic lenses will not come out. Are there also bolts from the back. I know it is very simple, but I do not want to force it. I have posted photos to show what I am talking about. Thanks

0 members like this

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by David Cotton on August 9, 2014 at 10:10am: Excellent. This just the help I needed. Thanks so much.

Comment by Jason Edge on August 9, 2014 at 9:50am: Did you remove the center aluminum ornament bar with the reflectors? You will go thru 3 sets of screws to remove it: 2 screws holding lower ends to ornament bar, 2 screws holding ornament bar to bracket, 2 screws holding bracket to tail light fixture. From there remove the upper and lower tail light screws, and gently wedge the tail light out with something thin, being careful not to crack. I touch of WD 40 can help remove it.

See complete center tail light ornament bar with reflectors, and a picture with tail light lense below:

RSS

Welcome to
63/64 Cadillac Website

Sign Up
or Sign In

Or sign in with:

Photos

Forum

64’ A/C Power Servo - Vacuum Actuator

Started by Jacob Foster in 1963/64 Cadillac Specific Discussion. Last reply by Linda M. Brooks on Monday. 2 Replies 0 Likes

Gents, good morning!I’m looking for advice on how to fix the A/C Power Servo on my 1964 Cadillac Deville. The unit itself seems to be working correctly, but the vacuum actuator is leaking off. Has…Continue

Transmission and power seats

Started by David Erickson in General Discussion. Last reply by Linda M. Brooks on Monday. 3 Replies 0 Likes

Couple of question on my 63 Park Avenue1. I had my car worked on last summer by my mechanic who restores casr primarily. He does not work on transmissions. He said there was a small transmission…Continue

1964 Cadillac Owners - Are You Missing the Inner Fender to Frame Rear Brace Rods?

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Linda M. Brooks on Sunday. 7 Replies 1 Like

Last night I was installing the freshly cad plated inner fender to frame rear support brace rods and remembered how this has been often missing on the many parts cars I have brought in. The thing is…Continue

63 & 64 Eldorados at Mecum Auction in Kissimmee

Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari on Friday. 1 Reply 0 Likes

Here is a 1963 & 1964 Eldorado I saw at Mecum auction in Kissimmee, Florida today. This was today’s main activity as part of the 2026 CLC Winter Reunion in Orlando. There are over 4,200 event at…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue