The temperature gauge of my 63 Eldorado does not work properly.
It goes slowly all the way up and stays there, while the true temperature is around 155-160 F (water in the radiator and/or the top of the thermostat housing).
Where should I start to solve the problem? The gauge itself, the temperature sensor, or the wiring? Or something else? The sensor is a new (aftermarket part) and the thermostat worked fine when I tested it in a saucepan.
Many thanks
-Samu
Comment
That is good news, Bob. I ordered 5 and will do a comparison with the original I have in my car.
Jason.
It recently bought an ACDelco temp sensor from Rockauto https://www.rockauto.com/en/moreinfo.php?pk=343530&cc=1320309&a...
It is working like it should, reading the temperature correctly.
That is good news indeed. Now, if they would only start reproducing the correct replacements. The list if defective replacement parts is growing!
Better late than never:
I finally plugged in the good used temp sensor bought from Jason, and the problem is solved.
The temp gauge stayed now at the lower 1/4 mark. The weather was allready quite cold (~35 degrees Fahrenheit), but with the previous sensor the gauge went up whatever the outside temperature was.
That test drive was the last one for this season. Case closed and a good start for the garage season.
-Samu
As Chris noted, most new temp sending units (at least the ones from China) are mis-calibrated and give a false hi reading. I have a good used sending unit that gives a resistance in the correct range I have seen for good sending units over the years for $20. I only have the one for now and the demand has been growing. I can ship to US destinations for $10 for a total of $30. If you want it, shoot me an email to jasonedge@nc.rr.com.
I was just talking about this with Jason the other day as my car is doing the same thing. The new temperature sensors can be junk straight out the box. I believe Jason might have an extra used original one. I just ordered one from him yesterday.
Started by Stephen Pechenik in Restoration Discussion. Last reply by Linda M. Brooks 12 hours ago. 3 Replies 0 Likes
I am readying my Fleetwood to be painted. I need to replace the driver's side left chrome eyebrow molding (below the headlights). It appears to be made from pot metal. Mine is broken and I need to…Continue
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion on Sunday. 0 Replies 0 Likes
Hi everyone I would like to know dose anybody here have a tissue holder fitted to their car if so could you please send me a picture of it thanks in advance Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion on Saturday. 0 Replies 0 Likes
CLC Membership dues are going up April 1. Join or Renew between now and March 31 and save! You can even renew with current rates for up to 3 years!Here is a breakdown of the rate increases Effective…Continue
Started by Jason Edge in Chapter Discussion on Friday. 0 Replies 0 Likes
Here is a breakdown of the rate increases Effective April 1:E-membership…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
February 15, 2026 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes
© 2026 Created by Jason Edge.
Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website