I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack.  Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings, tie rods, sway bar, ball joints, everything) on my 64 deville conv,  there is quite a bit of play in the steering.  At times it's hard to keep the car straight going down the highway.  When it starts drifting and you go to correct, it almost overcorrects and gets scary weaving back and forth trying to keep it center.  I'll try to use my original Maintenance manual to see how to address (maybe there's an adjustment on the worm gear or other adjustments on the steering box?) but wasn't sure if others have had similar issues.....  any help is appreciated.   thanks, Nile

Views: 109

Reply to This

Replies to This Discussion

Hi Nile,

     After all that front end work, there is an adjustment on the steering box, but it shouldn't be overdone.  On top of the box there is an allen key hole, set inside a nut.  You can see this looking over the fender and may have  get underneath the wrench it.  The nut (maybe 9/16 wrench) is loosened and the allen hole can be tightened 1/4 of a turn clockwise.  Hold the allen key in place while tightening the nut back up.  Unless the box is very old and worn, you might get some slack taken out.  I wouldn't do much more than 1/4 turn.  See if this helps at all.

Dennis DiBari, NY

Hi Nile,

     One more thought on the play in the steering.  Did you test/inspect you Rag Joint?  That can cause a lot of play in the steering as well.  I forgot to mention it with my first rejoinder.  Look at this first as it may be the culprit.  The slight steering box adjustment is your last resort.

Dennis DiBari  

Thank you Dennis for the help!  I love this website for this:  passing on knowledge.  I'm going to give this a shot!  thanks much.  Nile

Hi Nile,

     You are welcome!  Remember, if you adjust the steering box, no more than 1/8th to 1/4 turn clockwise.  The rag joint play is primarily important.  Best of luck with it!!

Dennis DiBari

RSS

Photos

  • Add Photos
  • View All

Forum

Headlight conversion

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Phillip Hill 19 hours ago. 2 Replies

I recently converted my dim yellow headlights to LED after nearly cleaning up a roo the other night see attached pics for before and after …Continue

What parts do you need for your Cadillac?

Started by Russ Austin in General Discussion. Last reply by Russ Austin on Thursday. 2 Replies

What parts to your need for your Cadillac?  Need a part to get it running or just to tidy things up a bit?  Starters to nice A pillar moldings, my 1500 squarer footing shop is packed with parts. …Continue

Take heads off for rebuild

Started by Ian Arnold in 1963/64 Cadillac Specific Discussion on Wednesday. 0 Replies

Compression test 15 years ago was good. Not a lot of miles since then. Summer car.Last year had a oil pressure issue. Found an aluminum flake had stuck open oil pressure relief valve. (Low pressure…Continue

Dino Diaries - Feb 28, 2025: What's Good for the Convertible is Good for the Coupe!

Started by Jason Edge in General Discussion. Last reply by Cees de Bunje on Wednesday. 10 Replies

I have made some "factory" upgrades to my 64 Coupe de Ville by installing some options available to my Coupe de Ville such as power vent windows, tilt steering column, am/fm, 3 way rearview mirror,…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2026   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service