Question about rubber mounts under the hood

Along the painted metal portion above the grill there are small rubber type pieces along the length of the grill that I'm assuming are to fit against the hood.  Does anyone know where to find those pieces  I have one that is missing and a couple that appear broken or torn.  I've been running into some pretty tough judges at shows.

Views: 119

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Jason Edge on September 12, 2012 at 11:52am

When I saw them yesterday when I was quickly scanning the Steele Rubber online catalog my eyes immediately went to the bottom and mentally inverted them right sight up but wanted to make sure with the Cadillac part # they gave. I did go back and look at mine and I have one that is almost missing one tab..so it will be a nice little upgrade on my CDV also. If someone is missing say 1 or 2 of them, I will have a 6 extras to sell for say a couple of bucks each that I can combine with an order of something else. If all of your's are well worn I would go online and just order a set.

Comment by Kevin Williams on September 12, 2012 at 9:59am

Thanks Jason, mine have no thickness left to them at all.  Looking at the listing it would make sense that these would keep the hood from banging onto the grill.  Seeing this picture I think I've seen these but not knowing what they looked like when new I passed over them.

Again thank you...you are two for three now all I need to find are those tin inserts.  One popped up on ebay I think yesterday and keeping an eye on it.

Comment by Jason Edge on September 12, 2012 at 4:41am

I just ordered 2 sets for myself.

Comment by Jason Edge on September 12, 2012 at 4:30am

Kevin, Mine are all there but painted over. I think I can gently remove the paint but would just rather have new. I think I've tried to remove used but without much luck. I might try again.

Looking at the master parts book I think this is the part they are referring to as the Hood to Hood extension front Hood Panel Bumper which is part # 148 2384. Yesterday when I was looking thru Steele Rubber catalog I saw something that looked like them but upside down but wanted to go back and match #'s. I just pulled up there catalog and sure enough they say it replaced part # 148 2384. 

The Steele Rubber # is 33-0861-42 and are $1.60 each.

Go on line at www.steelerubber.com or call 1800-544-8665

Here is a picture of that listing...

Comment by Kevin Williams on September 11, 2012 at 11:49pm
Russ,
Jason just posted a photo of the pieces I'm trying to find...seems he is trying to find the same thing
Comment by Kevin Williams on September 11, 2012 at 11:41pm
Yes those are what I'm trying to find...I'm missing one and a couple of other that are cracked or missing a portion.
I've checked eBay for months now and checked countless sites but just can find any reference to these pieces?
Comment by Jason Edge on September 11, 2012 at 11:10pm

Kevin,
I meant to get back with you. I read this morning and thought you were talking about the small rubber bumpers on top of the upper grill top triangular painted piece. These are the items circled in picture below. I pulled up Steele Rubber's PDF Catalog thinking they would have them but couldn't locate them right way but didn't research from end to end. If this is what you  need I would like some new ones for my 64 CDV Also. Here is the picture:

Photos

  • Add Photos
  • View All

Forum

Lower Front Grille 64 Fleetwood

Started by Logan Robb in 1963/64 Cadillac Specific Discussion 5 hours ago. 0 Replies

As I prepare for the CLC Fall Festival next weekend, I find myself finishing up everything on my list that I wanted to get done ACCEPT the lower front grille. Jason put together a SUPERB front grill…Continue

The End is Near ... for Parts Car #60

Started by Jason Edge in General Discussion 20 hours ago. 0 Replies

When I pull a parts car in it comes off the car hauler until I am ready to remove the under-carriage. At that time it goes back up so the front stuff (wheels, upper & lower control arms,…Continue

A Quick Hello & Sneak Peek at Next Newsletter

Started by Jason Edge in General Discussion yesterday. 0 Replies

Thought I would share a quick picture of our next newsletter feature Dennis Dibari's 1964 Series 62 Coupe. After a long driving tour road trip and some personal issues, and a quick beach trip this…Continue

Special Order Paint Cost for 1964 - Question

Started by Joe McDonald in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 1 Reply

So I've been trying to price out the original cost for my 1964 Coupe deVille with all of the options it was ordered with.This car was a Special Order paint job code 00 on the data tag. After pulling…Continue

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service