Well,, 63 got in. due to work, unable to get out, plus some concern about the leaking radiator,, so i decided to crank er up, put some water in the radiator and went on quick ride, about 5 miles... i noticed something i didnt feel during original drive... it drives strait, no problem,, wen i hit brake it pulls right pretty good.
I ran through the old bills from about 87 or so.. there has been suspension work, new heavy duty shocks in last couple thousands miles,,prior owner said he put a"cherry bomb" on it for some noise, I dont particularly like loud cars, so any idea how to get rid of that thing,,I odnt like all that grumble..
I didn't notice anything else on that short little run.. Radiator be in next week, so i can take on a better ride then...oh,, there is a bit plastic container on the driver side toward the front of the engine,, i am assuming it may be the windshield washer? holds a couple quarts according to the markings. It has a hose that runs up to the firewall.. or is ti something else.. it kind of sits by it self..I got the manual out and started checking stuff with it, but didnt see that part.
Any thought s on the pull during break would be appreciated.
Sincerely
Kim
Tags:
ok, I was doing some reading in the SM,, read the suspension section, under the diagnosis chart, it has a column for "pulls to one side" has a list of items,, but the car does nt seem to pull while driving, only when brake is applied.
so i went to braking section, and the description was more specific,, pulls when braking, and list out a set of fixes.
so is there a relationship between the two, that it would be first best to go to the suspension fixes,,and if that did not fix the pull then I should go to the braking fixes?
If it is the bushings, how would it be identified on the car, as it sits, are they loose? do they look visually worn out, or does it have to be removed, and checked for wear, similarly, if it were breaks, would there be a visual clue that the conditions exist for the pull upon application?
again, please excuse all the questions of ignorance,
Sincerely
Can't see why not follow the recommendations in the shop manual. Do the checks and fixes. Mostly it will cost you time and if you find anything wrong its better finding out on the driveway than on the street. A 2,5 ton car not able to brake...
My car pulled hard to right when braking. It was the right side upper control arm bushings. Its a known occurrence from bad bushings. If you open your hood and look on the bushings you should see if they look okay. Meaning the shaft should be centered in the bushings both sides. If not they might be the cause of the pulling. Then crawl under the car and check all suspension parts to see what they look like. You might find some other issues.
My left side in fairly good condition:
I dont see those metal bars in the Manual drawing, its that some sort of addition you added for stability?
Its home made to be used when removing bushings and installing them again. This way I don't deform any parts and can push in the new bushing safely.
Bought a Bushing Installation / Removal Tool and added a few home made parts. Think 100 USD is a bit over priced, but the set did work good. And will work next time as well. Tools is a on-time cost, so don't save on tools.
To get the car up in air safely I use a combination of hydraulic ramps and a jack. Then placing the car on jack stands. Thinks its a lot faster and safer than working the jack on one side "tilting" the car.
Someone might have a good reason not to place the jack below the differential casing on the rear axel. But for me I think its okay.
Cheapest is just to open hood and look on the bushings, 30 seconds at the most. If the right upper control arm bushings are bad then you found your main problem. Not discounting the possibility that brakes are bad as well.
Does sound like a good reason. It should be fastened with a torque of 60 foot-pounds.
Maybe better get over all the other bushings below the car to make sure they are fastened accordingly. If one is loose...
Hi Kim, welcome to the 63-64 web site!
The bushing bolts being loose could cause the brake pull, but, it is an indication that the bolts were tightened with the suspension hanging and the car not supported by the suspension. Those bolts are supposed to be tightened when the car is sitting on all four wheels. It would be a good move to check all the bushing pivot bolts on the upper and lower control arms to be sure they are at the proper torque. Inspect all the bushings, upper and lower control arms and the strut bushings in the number one cross member. Be sure they all are in good condition.
Congratulations on your new car!!
thanks for the further information,, i will get a look at all of them..they are neat machines. i like the all metal dash, the dash components,, all the chrome, in and out,, just facisnating.. and the room!!!
i have the coupe, but i can only imagine a 4 door unit.
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by CHRIS CARLSON 18 hours ago. 1 Reply 0 Likes
I noticed this issue at the end of last summer/fall, but it seems to be getting worse as I have begun driving for the season again. When I drive the car and get everything good and warmed up, if I…Continue
Started by Jason Edge in General Discussion. Last reply by Logan Robb yesterday. 3 Replies 0 Likes
I recently picked up a rather large batch of parts from a contact that has sold their 63 and had left over parts. Here was one item I pulled that make me smile - a 1963 Indiana License Plate. For…Continue
Started by Jeff Donaldson in General Discussion. Last reply by Jeff Donaldson yesterday. 3 Replies 0 Likes
Has anyone bought new oem headlights from Lectric Limited? They want $150 for a set of new remanufactured ones. Any advice would be appreciated.JeffContinue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by