Anders's Discussions (1,153)

Search Forum

View

Discussions Replied To (1075) Replies Latest Activity

"Without any pictures its very hard to figure out anything. Poor body mounts wouldn't…"

Anders replied Apr 25 to Body mounts and loose feeling rear end.

 8 Apr 25
Reply by Tony and Ginny 429

"The compression is a bit worrying. Was it a complete rebuild, or just heads and gask…"

Anders replied Apr 24 to Head Gasket on 429 - If it were put on upside down, what would happen?

 27 on Friday
Reply by Jason Edge

"When installing the front yoke into the transmission housing seal you apply some tra…"

Anders replied Mar 14 to Transmission tail shaft bushing (s) and seal for 64 with TH400

 18 Apr 2
Reply by Norman Silverman

"I didn't say that any prior lung damage would help get past Covid. I said that there…"

Anders replied Mar 13 to I installed a Stereo System in my 64 Coupe de Ville Dino Today

 8 Mar 13
Reply by Anders

"Don't think you would get any vibration from that. But not sure what part you are re…"

Anders replied Mar 13 to Transmission tail shaft bushing (s) and seal for 64 with TH400

 18 Apr 2
Reply by Norman Silverman

"Yeah Ian. Only three people can light up at the same time. That is really a big prob…"

Anders replied Mar 10 to I installed a Stereo System in my 64 Coupe de Ville Dino Today

 8 Mar 13
Reply by Anders

"Hmm, my sender was completely rusted away. The filter in the bottom of the fuel tank…"

Anders replied Mar 10 to Gas Gauge Goes to Half Full

 6 Mar 10
Reply by Lee Martin

"Imagine doing a full EV-conversion. These cars would be perfect. A good sturdy frame…"

Anders replied Jan 7 to 1964 cadillac engine

 5 Jan 8
Reply by Tony and Ginny 429

"Sold for 24 000 USD."

Anders replied Dec 23, 2020 to No Reserve Auction on Chapter Member Jim Verraster's 1964 Cadillac Fleetwood 75 Auction

 1 Dec 23, 2020
Reply by Anders

"From the 1964 Cadillac Shop Manual: "

Anders replied Dec 19, 2020 to oil pressure, again,

 2 Dec 19, 2020
Reply by Anders

RSS

Photos

  • Add Photos
  • View All

Members

Forum

429 restoration

Started by Matti Roth in Restoration Discussion. Last reply by Tony and Ginny 429 1 hour ago. 6 Replies

Hello, and thanks for adding to group!I am restoring 1964 429 engine which I bought as dismantled. It is said to be smoking in driving and has been stored as parts for a year. It is most probably…Continue

Tags: #429

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 5 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 244 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

1964 Cadillac parts for sale... northern cali

Started by Jason in For Sale yesterday. 0 Replies

Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 cans) $40Convertible top latchValve coversHeadlight bezelRadioGas…Continue

Tags: Parts

Blog Posts

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Car lift and jack stands

Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments

I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …

Continue

Events

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service