11th Annual Cadillac Fall Festival
Event Details
Time: September 26, 2019 to September 29, 2019
Location: The Gilmore Car Museum, Hickory Corners, Michigan
City/Town: Hickory Corners
Website or Map: http://www.cadillacfallfestiv…
Event Type: clc, fall, festival, -, car, show
Organized By: CLCMRC
Latest Activity: Jun 20, 2019
Export to Outlook or iCal (.ics)
Event Description
THE 11TH-ANNUAL CADILLAC FALL FESTIVAL WILL TAKE PLACE SEPTEMBER 26-29, 2019
at the Museum & Research Center on the Gilmore Car Museum campus in Hickory Corners, Michigan. You can bet that all things Cadillac from 1903 to 2008, as well as the upscale La Salle marque, will be welcome as the Gilmore is home to the Cadillac & La Salle Club Museum. Prewar classic V-12s and V-16s, along with the fl ashy fi ns of the 1950s all the way up to the modern designs, will be celebrated with well-preserved originals from all decades. Wayne Kady, the designer of the 1971 Eldorado will be an honorary chief judge. Bus tours will include trips to the GM Heritage Center and GM Tech Center. Online registration is now open at www.cadillacfallfestival.com.
Comment Wall
Comment
-
Comment by Tony and Ginny 429 on June 20, 2019 at 1:25pm
-
During WW 2 a friend of my Grandfathers gave him a V12 Cadillac because he could not afford the price of gas to run the car
Sure gas was being rationed then
Not sure what year or other details about that
Just what my Grandfather told me
What years and models had the V 12 engines then ?
Enjoy
Photos
Members
Forum
Chapter Member? Got a 63 or 64 Cadillac for Sale? Let's Run it in the Newsletter!
Started by Jason Edge in For Sale. Last reply by Jason Edge 4 hours ago. 4 Replies 0 Likes
One of the new features of recent newsletters is a Member Classified Cars for Sale section.…Continue
vacuum canister
Started by Walt Timmerman in General Discussion. Last reply by Rob Shatsnider 9 hours ago. 15 Replies 0 Likes
what is the vacuum canister for that is behind the drivers front fender?After removing my fender I see its got a hole in the top but nothing is hooked to it and no line is laying there.Any help would…Continue
New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each
Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 15 hours ago. 10 Replies 0 Likes
As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue
63 coupedebille fuel pump issues
Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Daniel Grande 23 hours ago. 9 Replies 0 Likes
I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue
Blog Posts
New vehicle in the club
Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment 0 Likes
I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha. …
Torque converter grab when idling in Drive
Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments 0 Likes
Hi Everyone, been quite a while since i have been on here.
I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.
With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.
I've had the car dyno tuned and…
ContinueCan you help? Driveshaft Question....
Posted by Chris on May 30, 2021 at 8:55am 1 Comment 0 Likes
Hello!
Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…
ContinueThank you Kurt re: VIN location
Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments 0 Likes
I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations. Excellent information. Thanks a bundle.
Robert Pellow
Events
-
June 2021, 1963/64 Cadillac Chapter Virtual Meet-Up via Zoom
June 27, 2021 from 7pm to 8:30pm – Zoom
0 Comments 0 Likes
© 2021 Created by Jason Edge.
Powered by
RSVP for 11th Annual Cadillac Fall Festival to add comments!
Join 63/64 Cadillac Website