The 5 Main Things I Recommend to All New 1963/64 Cadillac Owners

Here are the 5 main things I recommend to all new 1963/64 Cadillac Owners:
 
Join the CLC (Cadillac & LaSalle Club).   To join go to www.CadillacLaSalleClub.org and click on Join.  There are many benefits to members starting with the monthly award winning Self-Starter magazine.  I have attached a list of benefits.
 
Join the CLC 1963/64 Cadillac Chapter. Once you are a member of the CLC, shoot me an email to jasonedge@nc.rr.com with your CLC membership # and I will sign you up to our Free Chapter!
 
- Join the 1963/64 Cadillac Website at www.6364cadillac.com. You will find tons of helpful technical information, especially on our Help page (www.help.6364cadillac.com), a list of parts suppliers including myself (www.parts.6364cadillac.com) , and MUCH MORE! To join just go to the website and click on sign up to get a username and password.
 
- Join a local CLC Region or CLC International Affiliate.  There is nothing like the fellowship and camaraderie of joining a local CLC Region.  In addition to the local meet-ups and car show, cruise-ins, etc.; they can also help you find local shops for maintenance and restoration of your Cadillac!  For a list of all Regions and Chapters click on http://www.cadillaclasalleclub.org/page/regions_chapters
 
- Buy a Cadillac Shop Manual! It should be your 1st purchase if you do not already have one. You can almost always find them on eBay.  You will find originals, reprints, and digital versions.
 
Jason Edge
Director 1963/64 Cadillac Chapter

Views: 580

Attachments:

Reply to This

Photos

  • Add Photos
  • View All

Forum

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 8 hours ago. 5 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 22 hours ago. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 23 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Organizing For Sale?

Started by Anders in Suggestion Box. Last reply by Jason Edge yesterday. 1 Reply

Been looking on the For Sale forum. Not sure if possible or not, but it might be good if there would be sub-forums so cars go in one area and maybe spares could be sorted in a way as well. No idea…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service