63/64 Cadillac Website

side marker w script

I 3D printed a Cadillac script for my cornering light which has been also modified to work as a side marker.

1 member likes this

View Full Size

Tags:

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Dennis P. DiBari on May 21, 2025 at 6:34pm: Kurt,

I love your cornering lights and lens script on your Caddy!!!!!!

Dennis DiBari

Comment by Bill Wolf on May 21, 2025 at 4:41pm: That looks great. I like the font.

Comment by Kurt on November 27, 2023 at 5:54pm: Thanks for the comments. It is just PLA plasic. 3D printing is a fun hobby. Would love to have a 3D printer that prints in metal but that is unlikely due to the cost. I haven't considered metal casting but might look into that.

Comment by Roy Brosi on November 27, 2023 at 12:28pm: Looks great! Like it should have been there all along.

Comment by Jason Edge on November 23, 2023 at 8:27am: Very cool! That looks a lot like the 63 dash script.

Welcome to
63/64 Cadillac Website

Sign Up
or Sign In

Or sign in with:

Photos

Forum

Rear Upper trailing arm, Rear ball joint, Rear lower trailing arms

Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Norman Silverman 2 hours ago. 4 Replies 0 Likes

Has anyone replaced any/all of these parts? If so, where did you buy them? Also, and most importantly, did replacing them change any characteristic of the car, like maybe reduce driveline…Continue

Dino's Gas Lines Removed - Clean Up or Replace --> Member Advice

Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge 6 hours ago. 11 Replies 0 Likes

As part of my undercarriage cleanup and and restoration of my 64 Coupe de Ville 'Dino', I removed both gas lines (my car has AC so it has a 5/16" supply line and 1/4" vent return line) to gain better…Continue

1963/64 Cadillac Starting - Cranking System Basics

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Chris McBride 7 hours ago. 17 Replies 1 Like

I have had this info written up for some time and meant to post so here it is. I will link to this from our Help Page:1963/64 Cadillac Starting - Cranking System Basics Wiring You have a positive…Continue

Free cylinder heads and diffential in Phoenix metropolitan area

Started by Chris McBride in 1963/64 Cadillac Specific Discussion 7 hours ago. 0 Replies 0 Likes

Cleaning the shed - free partsI have no interest in shipping.Parts are located in Phoenix metropolitan area. Zip code is 85257. Nearest major intersections are Thomas Road and Scottsdale Road.Two…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue