"Thanks very much Dennis.
Peter."
Peter Greenway's Discussions
Pre shaped bench seat foam and springs
Started this discussion. Last reply by Peter Greenway Sep 29, 2025. 4 Replies 0 Likes
Hello, can anyone recommend where I can get pre-shaped foam for a bench seat?Also can anyone recommend where I can get new seat springs for a bench seat?Thanks.Peter. Continue
Pertronix Ignition Power Relay Installation.
Started this discussion. Last reply by Peter Greenway Jan 12, 2024. 11 Replies 1 Like
Has anybody installed the Pertronix power relay for the Pertronix ignitor electronic ignition?I have installed one on my 63 car and as per the instructions I had to also install the isolation diode…Continue
Replacement seat cover kits.
Started this discussion. Last reply by Peter Greenway Jan 30, 2023. 3 Replies 0 Likes
Hello, I have a 63 4-door sedan and want to replace all the seat covers on the front bench and rear seats. Can anyone recommend the best place to buy the complete seat kits (already stitched up)…Continue
63 Lower Front Bumper Ends?
Started this discussion. Last reply by Peter Greenway Sep 26, 2022. 3 Replies 0 Likes
I'm looking for 2 good condition lower front bumper ends for a 1963 car. Can anyone help please?Continue
Peter Greenway's Page
Latest Activity
"Hi Peter,
I did not know about the lip in the foam on some of the seats and that they are available. I hope you can find them on line. You are right about the springs; they are as old as ours. I have never seen…"
"Hi Dennis,
Thanks for that.
My upholsterer has said because my foam is molded with a lip it is difficult to cut new foam to shape and fit and he will not do it. He says he has seen on-line companies that sell pre-shaped molded foam, so I'm…"
"Hi Peter,
I plan to pull all my seats this upcoming winter and have them reupholstered with the original fabric. The upholsterer will take them to his shop and is redoing all the foam and the upholstery. He does top…"
Pre shaped bench seat foam and springs
Hello, can anyone recommend where I can get pre-shaped foam for a bench seat?Also can anyone recommend where I can get new seat springs for a bench seat?Thanks.Peter. See More
"It seems the generator has gone faulty and only putting out 2.0v. I would guess I've damaged the internal diodes inside the rectifier."
"I've managed to get a wire through the cranking harness grommet and connected it to the ACC switched terminal. When connected to the coil I still got the same results with the GEN light. So I removed the relay, wiring and diode and reinstalled…"
"With lower instrument panel (dash) cover below steering column removed and with a good light you should be able to fish a wire through grommet and see it coming through and pull toward the fuse box. Just to note, The dash pad comes out…"
"If I use the cranking harness grommet can I get to it up under the dash without removing the pad?"
"The cranking harness grommet dead center behind engine is probably your best route.
You should see a rubber plug over on left driver side even if not used. It is just another option for running wires, etc into the cabin. See oval plug/grommet…"
"Thanks Jason I will look at the Pertronix Ignition comparison page.
I have found the ACC fuse terminal on the side of the box and although it is being used I can tap into that ok. See attached picture.
I don't have a rubber grommet under…"
"That is an ignitor I series unit. The oldest unit and one I think you would want to skip over once you read out Pertronix Ignitor Ignition & Flamethrower I, II, and III Comparison Help Page.
You will still need to get a…"
"I can understand what you are saying Russ. If I I run a new switched wire from the fuse box, what's the best way to get it through the fire wall to the coil?
I'm attaching pictures of the Pertronix instructions to clarify things, I…"
"Just to clarify I haven't installed the Pertronix ignitor yet. I started with the power relay first to ensure I had full 12v feed to the ignitor as per the instructions. My Pertronix model number is 1181LS. I will attached pictures of the…"
"Remove the isolation diode from the scene. Run a switch power wire to the coil and that will solve your problem. You can remove the resistor wire but you will need to take the dash pad off to access the ignition wire harness where it is spliced into…"
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1963 Series 62 4 door sedan 4 window. Colour; Briar Rose.
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- 34251
- 1963/64 Cadillac Chapter Member?
- Yes
Comment Wall (1 comment)
- At 6:53pm on November 18, 2021,
Jason Edge said…
Welcome to the 63/64 Cadillac Website.
This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the Chapter.
- Click on www.join.6364cadillac.com for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club.Be sure and check out all the links and pages and make yourself at home. The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.
Photos
Members
Forum
No AC 1963 Eldorado Unique Dash End Panels
Started by Jason Edge in General Discussion on Sunday. 0 Replies 0 Likes
As I was documenting the non-AC 63 Eldorado parts car I bought in a couple months ago, the solid panel dash end panels intrigued me and thought I would share a couple of pictures and thoughts. First,…Continue
For Sale - Fresh Chrome 1963 Series 62 Conv/CDV/Eldorado door panel chrome bezels
Started by Anthony Vanacore in For Sale. Last reply by Jason Edge on Sunday. 4 Replies 0 Likes
Hello,My father and I are restoring our 63 series 62 conv, we had the chrome bezels for the window/seat switches rechromed. During this process we also installed factory power door locks to the…Continue
WTB 63 Series 62 Original Trunk Material
Started by Anthony Vanacore in Wanted to Buy. Last reply by Russ Austin on Friday. 1 Reply 0 Likes
Hello,I am looking for an original trunk for a series 62 convertible. Condition does not need to be perfect and does not need to be complete, I am looking for a set that I can use as a template. I…Continue
Parts to replace Power Brake and Master Cylinder for 1964 Eldorado
Started by Remco Waller in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari Apr 27. 1 Reply 0 Likes
I have a 1964 Eldorado and based on paperwork received with the purchase the Power Brake unit & master Cylinder were never replaced. The brakes are working currently well but as pre-caution I…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
-
May 17, 2026 - 63/64 Cadillac Chapter Zoom Meet-Up
May 17, 2026 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
Videos
© 2026 Created by Jason Edge.
Powered by
