Hi.
Where is the best place to purchase good quality motor mounts/trans mounts for my 1964 SDV? I see that Rock Auto has them for $8 and change, and others for $24 and change. Big difference. Is there a better place to buy them from?
Thanks
Norm
Comment
Don't know why I had not received notice of these responses till today. Thanks Ronnie for the info, and Clovis for your confidence. Jason, I'll take a set of motor mounts from you. The fact that they may be cheaper elsewhere is less important to me than the fact that you as a dedicated and knowledgeable resource for our cars, are supported. To me that's a better "value" than just a cheaper price. I'll send you a direct email and you can quote me price with shipping.
Should be no difference. Should be part # 2238 as part of the catalog # as seen below with the Anchor and Duralast (AutoZone) sourced mounts I have on hand. I probably have 20 sets but the prices out there on some sites have really dropped recently, below what I paid, and will hold on to mine for the long haul. I think I paid about $10 each for mine and had priced to sell at $12.50 each or $25 a set but again if you can get them cheaper that is the way to go.
Started by Jeff Donaldson in General Discussion. Last reply by Jason Edge 12 hours ago. 2 Replies 0 Likes
Hello Everyone,I tried to remove my clock today and couldn't seem to get it to rotate more than a 16th to an 8th of an inch. I followed the instuctions in the manual (counterclockwise approximately…Continue
Started by Jason Edge in General Discussion yesterday. 0 Replies 0 Likes
I have very limited space in my 3 bay garage with the left and right bay used for storage and work tables, etc leaving the narrow center aisle for my 1964 Coupe de Ville Dino. Six years ago I bought…Continue
Started by Stephen Pechenik in General Discussion. Last reply by Bill Wolf yesterday. 13 Replies 0 Likes
Hello Co-Members,I recently purchased a low mileage1963 Sedan Deville Park Avenue. It is extremely solid and runs well. Neverthelss, it has minor problems that need to be addressed before I can…Continue
Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Wayne Morris on Saturday. 6 Replies 0 Likes
I am in the process of trying to install body side molding. I have completed installing the two front fender pieces and now trying ti figure out the rest.…Continue
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
ContinuePosted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
© 2024 Created by Jason Edge. Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website