Greetings everyone and Happy Easter to all! I finally got the rebuilt heads on my 63. Thanks Jason for the heads and Jason and Russ for the head bolts. I started her yesterday and went for a nice cruise today. Man, this ole' girl knows how to scoot! Now I have a carb question. I found several issues with carb and intake gaskets during the teardown that indicated why the engine was running lean. Now that everything has been corrected I am getting a very slight black smoke from the tail pipes at idle with the mixture screws closed completely. I set the timing and idle speed to factory specs with the vacuum line disconnected. Before the heads were replaced the mixture screws were turned out about 1 1/2 turns each. From the part # on my carb it is from a 65 429. Could that be the problem? I have a 600 cfm Edelbrock carb that I considered using but am not sure how to make it work the throttle and Jetaway linkage. Any reputable carb rebuilders out there? I have watched many videos from Carburetors and More but their reviews do not speak highly. Thanks to all.

Facebook Facebook

Views: 303

Reply to This

Replies to This Discussion

Ok, I just had a brainstorm thought. I did replace the original phenolic carp spacer with a reproduction unit from OPGI. The 3/8" connection on the original for the PCV connection had a very large hole for the vacuum inlet. The aftermarket spacer had a very small hole, about 1/8" ID but still accepted the 3/8" ID hose. Maybe, just maybe, I am not drawing enough air through the PCV Valve which would cause the slight overly rich mixture. Hmm, I have a plan. I will repost after I do some further testing. Stay tuned boys and girls. Happy Easter to all!

The carter adjustments are 3 turns for the air mixture screw, a 1 1/2 for the idle mixture screws.

The car should stall out with the fuel mixture screws turned in. That is telling me you have a vacuum leak somewhere.  As Tony mentioned, are you capping the vac line to the distrib?

Turning the air mix screw out is going to lean out the fuel mixture. It is difficult for me to get the mixture correct, so I installed a air/fuel mixture monitor to get it spot on.

RSS

Photos

  • Add Photos
  • View All

Forum

Logans Intake Project, 1964 Fleetwood, Progress Report #3

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb 11 hours ago. 5 Replies

Not much of an Update and Questions: I was inspecting the top end and had removed the air cleaner in preparation to replace the intake. It was dirty so decided it needed a wipe down. My goof was…Continue

headlight / dimmer switch confusion (63 Sedan Deville)

Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf yesterday. 4 Replies

The schematics are from the repair manual and show a LIGHT BLUE wire coming from the headlight switch to the dimmer switch. From the dimmer switch to the low beams on a TAN wire and to the high beams…Continue

Replacement Front Crankshaft Seal - 1964 Eldorado (429ci)

Started by Michael Stinson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 2 Replies

My mechanic is having difficulty sourcing a front crankshaft seal.  Can anyone recommend a replacement front crankshaft seal, and where to purchase?  Amazon has a few that I think(?) are replacements…Continue

Tags: Seal, Crankshaft, Front

Original Rim Color

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Stinson yesterday. 3 Replies

When I get some new shoes for my 64 Fleetwood, I'd like to recondition the rims. I'd thought of getting them powder coated, and still plan to eventually, but the $700 quote I received shunted that…Continue

Blog Posts

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service