It appears the only way to replace the Cornering Lights bulbs is to remove the entire bulb housing (in front of the front wheel wells). Is this correct? Or is there a better way?
Mike Vogler
Tags:
Thank you, Jason. This will save me from crawling under the car! The shop manual would have me removing the housing (at least as I read it).
Mike
Jason,
Good Morning. All of the screws are frozen tight. I soaked the screw heads with WD40 and around the seal, gently tapped each one through a screw driver with a hammer. No luck. My concern is even if I remove the housing (to get better access to the screws where they screw into the housing) I may still have to drill out each screw. Not a pleasant thought.
Do you have 14 (15) lens crews I can purchase (before I try to drill out the frozen screws)?
Thank you, again.
Mike Vogler
I have plenty of those screws. Parting cars out I have run into some stubborn screws. I would use a new #2 Phillips bit in one of those hand drivers that accepts bits. … or use a newer excellent condition #2 Phillips screwdriver. You do not want to use a worn Phillips head here. I will also say you really need to put some Hulk pressure on it as you turn. Firmly tapping the screwdriver with hammer can help loosen the threads. If it starts to slip … stop and spray something more aggressive on the screw like PB Blaster and wait overnight. I can’t remember ever having to drill one out and have run across some tough ones. Use an excellent Phillips tip and a lot of force and the screws should back out unless the screw heads have already been compromised. If you have to drill out use cobalt bits made for hard metal.
There are square shank screwdrivers that allow you to attach an adjustable wrench. That is about all I use at this point. That way all your energy can be for pushing in and not turning.
Jason,
Thank you again for the tips. I'll give it a shot!
Mike
Tony,
Thank for the advise. I'll give it a shot.
Re: Duct tape and a wire coat hanger: My wife is always amazed with my use of these items (notwithstanding the mocking I receiving. It may not be pretty, but they work!)
Thanks again.
Mike
Most screw drivers are shaped on the handle, to allow a ring spanner to be used on them.
Depending on the size of the screw driver, it will generally be a 3/4, 13/16 or 7/8.
Simply push in hard and turn the ring spanner..... easy leverage.
Sometimes, a light tap on the end of the screw driver with a hammer first, will help too.
Just to make sure we are on the same page, I think Kevin is referring to a box end wrench when he says ring spanner. I had never heard the term spanner used instead of wrench until I heard it from my UK friends way back.
What the hell do you guys call it..... LOL
Hunk of steel, with a slight bend in each end near the ring.
3/4 on one end, maybe 7/8 the other end, in the shape of a ring.
Hence, a ring spanner..... bloody yanks LOL
Box end wrench..... about time to came to Australia for some lessons in what things are called, you bloody North Carolina hillbilly.
I think it is the term “spanner” that would throw us NC hillbilly folk.
Started by Mack in 1963/64 Cadillac Specific Discussion on Tuesday. 0 Replies 0 Likes
Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue
Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith on Tuesday. 1 Reply 0 Likes
I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue
Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies 0 Likes
I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies 0 Likes
In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue
© 2024 Created by Jason Edge.
Powered by