Efi conversion
Hello all, I was wondering if anyone has done an efi conversion on their vehicle. I had the Holley Sniper installed and am very happy with the system except for the very annoying noise coming from the in line fuel pump. I am looking to go to an in tank pump but the retro fit pumps from Holley are for tanks that are at least 7 inches deep. Just wondering if anyone has dealt with this same issue. I do apologize if I have posted this in the wrong area as I am not super familiar with the site. Thanks for any input or advise
Replies to This Discussion
-
Permalink Reply by Michael Forte on
-
Hi Charles,
I have the Holley Sniper in my car and I'm using an in-tank pump. I used the Holley in-tank module part number 12-130, but that is for tanks 7" deep at a minimum, so I had to modify the way it drops in. I also bought a new tank (The same one they sell at OPGI) and it has a recess stamped in it that creates room for modern drop in EFI pumps. The orginal tank doesn't have this recess. Anyway, I had to modify the pump and the mod isn't for the faint of heart because the pump is expensive. You basically have to modify the bracket and the tubing so that it drops in on an angle instead of straight down. The pickup Holley uses is called "hydramat". Holley makes different shapes than the straight piece provided. I can't recall which one I used on mine. I've had mine running since 2018 and never had an issue - the sniper is the best mod I ever made and you really can't tell it's there under the factory air cleaner (which I modified to fit the larger sniper inlet).
Hope that helps!
-
-
Just found this article. Wish this was available in 2018 when I did mine...How To Install A Sniper EFI Fuel Pump Module Kit Into A Shallow Fue...
Photos
Members
Forum
Burning Rubber
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 2 hours ago. 6 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Gas gauge only reads half when full
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Wednesday. 1 Reply 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson Feb 15. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
