Neither of my cornering lights are working. I started by focusing on drivers side. I removed the entire assembly and cleaned it up, replaced the wire to the socket, cleaned and lubricated the socket and spring. Made sure light now worked by attaching directly to battery terminals. Reinstalled assembly and plugged it back in and no work. Attached a separate ground directly to the battery terminal and still no work. I checked orange power wire coming in and no power. I have the ignition turned on, signal on, headlights on and still no power to orange wire. Everything working but the corner light. Passenger side does not work either but have not done anything on that side yet. Figure one side at a time. Where should I look next. I have a manual. Thanks Larry
Tags:
Thats all you will get with just the top clamp removed. There is a bottom clam as well. Be farefull to not damage the steering rag joint.
Loosened off the two bottom bolts at steering column base clamp and the two bottom floor bolt which dropped column enough to get the job done. Once again thanks to all for the tips and guidance. Larry
Congrats on the fix! ps. I have been staring at an outer T-3 headlamp on that last parts car still up on the car hauler. If it works and you still need one it has your name on it.
If he doesn't want it, I would be interested.
Tony, Larry had been waiting a long time for good outer T3 and was next up on the Wait List. I have one other Chapter member on the list after Larry, so you would be #2 in line after Larry gets this one. I assume you need one outer T3.
I do have 6 tested inner Hi Beam T3's for you or anyone that needs that T3 headlamp.
Thank you Jason. I ended up ordering one from Russ.
That is great. They are getting harder and harder to find. If anyone else needs the inner hi beams I have 6 and they are $15 each for Chapter Members.
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by CHRIS CARLSON 6 hours ago. 1 Reply 0 Likes
Hey everyone, I need to replace my transmission input seal before spring starts, I’ve been losing a lot of fluid post Sunday drive. I figured I’d do the rear main seal service bulletin at the same…Continue
Started by Michael Monson in Wanted to Buy. Last reply by Michael Monson on Thursday. 2 Replies 0 Likes
Looking for a heater control valve 9.795 for my 1964 Deville. ThanksContinue
Started by Jeff Donaldson in General Discussion. Last reply by Logan Robb on Tuesday. 4 Replies 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kurt on Sunday. 7 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
© 2026 Created by Jason Edge.
Powered by