Gear for power vent window
Im having a hard time locating the gear for the power vent window in my 64 Eldo. The existing one has 14 teeth and all I seem to be finding are ones with 17 teeth. Any suggestions?
Thanks
Replies to This Discussion
-
Permalink Reply by Kurt on
-
These are what I bought a couple of years ago, recommended by Jason. They work perfectly.
https://www.ebay.com/itm/124193882376?mkcid=16&mkevt=1&mkri...
-
Permalink Reply by Russ Austin on
-
Caddy Daddy has them.
-
-
The ones from Caddy Daddy and ebay have 17 teeth, mine have 14 teeth but I eventually found them elsewhere.
thanks
-
-
I went back & checked the gears I replaced a while back & yes, the originals have 14 teeth. I don't have any pictures of the steel replacement gears I installed so I can't say for sure how many teeth they have. The picture of the gears on the website have 17 teeth but could be a sample pic & not the actual part. All I do know is that the gears fit properly & mesh properly & the power vents work perfectly. The teeth on the steel replacement gears should not strip like the soft aluminum originals.
-
-
I installed the aftermarket gear on my left front vent. It opens and closes as it should but only opens to 45*.
-
-
I actually upgraded my car to power vents and noticed that the manual crank vents did open wider. I just assumed it was normal for the power vents to open less wide but don't know if the replacement gears are a factor there. The original gears in the regulators I received were trashed so I never had a chance to see how wide they opened with them. I estimate that my vents open to about a 105 degree angle. Is your right vent still using the factory gear? If so, how wide does it open? Here's a pic of mine opened as far as it goes.
-
-
Sorry. It opens to 90* not 45. My original passenger vent opens to about 105* as yours do Kurt. I'm pretty sure that I installed the aftermarket gear correctly but maybe not. Has anyone else had the same 90* result after installing the aftermarket gears?
Cheers
Jeff
-
-
-
Permalink Reply by Jason Edge on
-
The 17 tooth gears sold by HydroElectric that I installed and I believe Kurt open the window well past the 95 degree angle. I can opening it until it is pushing air back and at me like seen in Kurt's pictures.
You can find them on eBay as seen with Kurt's link, or on HydroElectric site at the links on our Parts & Service Page.Here is the HydroElectric entry with with links reposted:
Hydro Electric - www.hydroe.com
Convertible Tops and related supplies including Power Vent Window Gears: LH Gear, RH Gear
Punta Gorda, FL 800-343-4261 941-639-0437Unless HydroElectric has started selling a different gear as a replacement it should open the window up as seen in Kurt's picture.
-
-
I installed the same gear as H E sells. It seemed to only go in one way with no room for adjustment but it's possible I got it wrong. No idea.....! I'll have to take it out again and take a look. Thanks for the feedback.
-
-
Perhaps you put the RH side on LH side and vice versa? You can look at the stock pictures for comparison when you pull them if not stamped L & R.
-
-
Perhaps; I did have a left and a right....Lol. I installed the one that looked like the one I took out. I'm not going to pull my car out until the end of March so I will report in when I get it figured out. Thanks for your help Jason!
Jeff
Photos
Members
Forum
Gas gauge only reads half when full
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion 13 hours ago. 0 Replies 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson on Sunday. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Down and Out for a Couple of Weeks --> but On the Mend
Started by Jason Edge in General Discussion. Last reply by Linda M. Brooks on Saturday. 2 Replies 0 Likes
I have been more than a bit quiet the past couple of weeks due to a really bad fall January 31 where I tore my right knee MCL ligament and ruptured the ACL Ligament. MCL will heal in time but ACL is…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
