Anybody out there have any experience or direction how to remove and replace the chrome trim moulding around the front door window glass?    Kevin

Views: 743

Reply to This

Replies to This Discussion

Kevin, the window has t come out. If its a 63, lucky U.  2 screws hold the bar in place. The rollers on the regulator ride in the bar, on the bottom of the window channel

2 screws on the back of the top chrome L shaped piece, hold it to the channel.

I got it replaced.  Thanks Russ.  Kevin

Kevin, is your window already out of the car? If not follow shop manual to remove glass. Then remove screws that hold the side & top trim to the lower channel assembly and gently pry the trim away from glass. When reinstalling I have used a lot of WD 40 to get the window back wedged into the seal and trim and lower channel.

Thanks Jason.  It worked!!!!  Got it.  Kevin

so u have to take the front window out in order to remove front window trim??? im in process of trying to remove trim or trying figure it out .but dont wanna take that Big window out 

JBailey,

Looking at picture below for front window trim with read arrows pointing to  left and right roof panel trim, and green arrows pointing to 5 pc reveal trim:

--> left, top and right reveal trim next to glass (green arrows) - removes with reveal removal tool. (windshield does not have to be removed)

--> bottom left and right reveal trim behind cowl  (bottom green arrows) - cowl has tom come off to access 5/16" screws that hold lower reveal brackets in place. (windshield does not have to be removed)

--> left and right front roof panel trim (red arrows) - WINDSHIELD AS TO COME UP TO ACCESS TRIM SCREWS).  The removal of this trim indicating removal of windshield is in the Shop manual (page 16-80 in 1963 manual; page 16-85 1964 manual),  

Once you remove the windshield and rubber seal you will then have access to a series of screws that holds the left and right front roof panel trim in place as seen below:

RSS

Photos

  • Add Photos
  • View All

Forum

VAPOR LOCK?

Started by Joel A Campos in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply

Hi All,    I finished my 429 transplant (Still a 429) last fall and cannot get the car to run correctly.  The carburetor, a stock Rochester 4gc was fully dismantled and cleaned and put back…Continue

64 trunk locks for sale.

Started by Russ Austin in General Discussion Apr 17. 0 Replies

I have 64 trunk locks for sale. A complete one, and a few with missing crests.All with the keys included.   Please email me at russ@thecadishack.com  to inquire about getting one. Continue

Vendor to refurbish my electrical antenna

Started by Remco Waller in 1963/64 Cadillac Specific Discussion. Last reply by Remco Waller Apr 13. 4 Replies

Hi, I own a 1964 Eldorado and the electrical antenna is no longer working smoothly and get sometimes stuck so like to refurbish it; who can help with a good vendor to do this.Remco WallerContinue

How to keep my soft top in good condition?

Started by Remco Waller in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith Apr 13. 1 Reply

Hi, I own a 1964 Eldorado convertible since last August and would love to get some input what the best way is to keep my soft top in good conditions.Which materials to use to clean / preserve the…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2026   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service