Hydramatic pics?
Does anyone have any good pics of the Hydramatic linkage? I'm trying to adjust the linkage per the shop manual. I have found that my manual rod is maxed out on adjustment which will not allow me to adjust it correctly. I suspect the manual lever is bent but I don't want to experiment with bending it until I know for sure what it should look like. The figures in the shop manual don't really help me determine what the lever should look like. Here's a pic of mine. The transmission is in park in the pic.
Replies to This Discussion
-
Permalink Reply by 3ft7bqmb7dryo on
-
The lever is up side down in the bracket. Reposition the tab 180 deg and install it into the lever.
-
Permalink Reply by Kurt on
-
Yep. You are correct. I eventually figured that out. It's all good now. This started out as a NSS adjustment project. My reverse lights stayed on in Low too. After I adjusted the linkage I could then adjust the NSS. Reverse lights are good now but the NSS still leaks vacuum going from Dr to N. It's fine going from P->N->Dr, there is no vacuum leak but not so going the other direction. From Dr to N is leaks vacuum then going into P holds vacuum again.
Members
Forum
Brake Booster not enough compression
Started by Rick Yasenchack in 1963/64 Cadillac Specific Discussion 1 hour ago. 0 Replies 0 Likes
I bought my 63 2-door convertible 62 series a few years back, previous owner said a new brake booster was just installed and that was why brake pedal was a rock. Did not know.Just had engine…Continue
Commercial Chassis Dual Battery Tray Questions
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 2 Replies 0 Likes
I'm looking for some info and hopefully some pictures on the commercial chassis dual battery setup. Is the second battery tray (driver side) , the same as the passenger side or is it mirrored? I'm…Continue
Meet-Up of 1964 Cadillacs in downtown El Segundo Car Show August 16
Started by Jason Edge in Chapter Discussion yesterday. 0 Replies 0 Likes
Chapter member Alan Clark and owner of a 1964 Eldorado sent this and wanted to share with everyone in case there are others nearby that might want to attend:"I'd like to invite the 63/64 chapter…Continue
The $120,000 1963 Eldorado on Bring a Trailer
Started by Jason Edge in General Discussion. Last reply by Jason Edge on Friday. 7 Replies 0 Likes
I have got a flood of email, texts, about the 63 Eldo that recently bid up to $120,000 and thought I would share for those that have not seen it.Here is the link:…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
