Hello,

Just wondering if anyone has photos to where I need to apply new SEM seam sealer on the front of the fenders to the inner top Cowl area and the corners of the Radiator support?

I am in the process of reinstalling new painted cowls and radiator support.

I know it had factory new but did not take photos of that area.my memory is not that good from two years back.

Thank you

Don

Views: 32

Reply to This

Replies to This Discussion

I have ZERO experience with seam sealer locations on this vehicle nor really any other vehicle. HOWEVER, I did grinde, sand, wire brush, fabricate and stitch in new floor pans and the whole interior floor on a 77 Lincoln Town Car. I put seam sealer on anything that remotely looked like a seam. I used tubes in a caulk gun as well as a 1 qt can. I used a brush and brushed over the seam first pushing the sealer as far in as I could. Then I ran a bead like it was a bead of silicone or a welding bead. Then I made it look as best I could. I think maybe the applied area was 2" wide when I was done. Followed by a coat of paint, I think it was better than what would have been quickly sprayed on by gun at the factory. 

Now, this area was going to be covered by butyl sheets and then isolation foam sheets, and then jute and carpet. So for someone to see it again, they'd be trying really hard. 

The area you are asking about seems a little more visible. In that case, I may use some painters tape and tape off the area you are working for more of a finished look. Otherwise, good luck!

Logan

Thank you For your message Logan

RSS

Photos

  • Add Photos
  • View All

Forum

Power Booster Install

Started by Rob Spring in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 3 hours ago. 5 Replies

Hey! I’ve seen the 63/64 power booster and master cylinder combination has been covered very clearly. I’m in the process of replacing mine. I was hoping someone could give me insight on a specific…Continue

Complete Front End Rebuild

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Mark Mata on Thursday. 1 Reply

I meant to make this a priority over the winter and didn't get that far. I've tried to source all the parts individually, but that is a daunting task. Partly because I don't want to miss any…Continue

1964 Cadillac Deville Neutral Safety switch and Oil Filter Housing Assembly

Started by Michael Monson in Wanted to Buy. Last reply by Russ Austin on Wednesday. 1 Reply

Hello, possibly looking a neutral safety switch for a 1964 Deville with the TH-400 and tilt steering.  Also, possibly looking for an oil filter housing assembly for a 1964 429 motor.  Starting to get…Continue

A Shout Out to Alan Grist & Some Pictures of His 1964 Series 62 4W Sedan

Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari on Wednesday. 2 Replies

As they say, Better Late Than Never!I want to give a shout out to 63/64 Chapter Member Alan Grist, who brought his 64 Series 62 Four Window Sedan, to the 2025 CLC Winter Board Meeting in Chattanooga,…Continue

Blog Posts

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 13 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service