Hello,

Just wondering if anyone has photos to where I need to apply new SEM seam sealer on the front of the fenders to the inner top Cowl area and the corners of the Radiator support?

I am in the process of reinstalling new painted cowls and radiator support.

I know it had factory new but did not take photos of that area.my memory is not that good from two years back.

Thank you

Don

Facebook Facebook

Views: 49

Reply to This

Replies to This Discussion

I have ZERO experience with seam sealer locations on this vehicle nor really any other vehicle. HOWEVER, I did grinde, sand, wire brush, fabricate and stitch in new floor pans and the whole interior floor on a 77 Lincoln Town Car. I put seam sealer on anything that remotely looked like a seam. I used tubes in a caulk gun as well as a 1 qt can. I used a brush and brushed over the seam first pushing the sealer as far in as I could. Then I ran a bead like it was a bead of silicone or a welding bead. Then I made it look as best I could. I think maybe the applied area was 2" wide when I was done. Followed by a coat of paint, I think it was better than what would have been quickly sprayed on by gun at the factory. 

Now, this area was going to be covered by butyl sheets and then isolation foam sheets, and then jute and carpet. So for someone to see it again, they'd be trying really hard. 

The area you are asking about seems a little more visible. In that case, I may use some painters tape and tape off the area you are working for more of a finished look. Otherwise, good luck!

Logan

Thank you For your message Logan

RSS

Photos

  • Add Photos
  • View All

Forum

1963 AC evaporator core leaking?

Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Mark Geertsma 4 minutes ago. 3 Replies

Hi all,Again I have issues with my AC system. Had it refilled recently but within a few days the system was empty again. The AC mechanic added tracer fluid to check for leaks, but there are no…Continue

Tags: 1963, core, evaporator, AC

Bleeding brakes

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Tony Prichard 12 hours ago. 4 Replies

I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue

Power steering fluid

Started by Bobby Brown in General Discussion. Last reply by Tony Prichard 12 hours ago. 7 Replies

My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue

seat foam replacement

Started by Kevin Robles in 1963/64 Cadillac Specific Discussion. Last reply by Kevin Robles on Wednesday. 3 Replies

does anyone out there have any experience with seat foam replacement on  a 63/64 Cadillac.  I had my seats reupolstered  many years ago in original leather/fabric and they still look great, but the…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service