Turn signal arm removal and gear shifter arm
Looking for assistance in removing the turn signal arm from the turn signal assembly on a non-tilt steering column. Does it screw in there or do I need to take this little retainer off the top or ??? Thanks in advance.
Also, is there something that keeps the pin in place for the gear shifter arm or does the pin just need to be pushed out? I see a thin metal spacer between the top of the shifter and the pin, but I’m not sure if that’s holding the pin in there or not.
’63 Fleetwood Series 75
turn signal switch
shifter
Replies to This Discussion
-
Permalink Reply by Dennis P. DiBari on
-
Hi Brandon,
Check that steering column diagram I sent you last week (The one you had to Google). It has all the parts of the steering column listed from top to bottom. It's the one Jason posted.
Dennis DiBari
-
Permalink Reply by Brandon N. on
-
I did but it didn’t help much.
-
Permalink Reply by Russ Austin on
-
The turn signal arm screw out. There are 2 flat spots where a wrench will fit. The shift lever pin is pushed out. I use a small brass punch and a hammer. Yes, there is a shim plate, so get that as well when the arm comes out. Take not as to what side it is on.
Photos
Members
Forum
Gas gauge only reads half when full
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion 16 hours ago. 0 Replies 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson on Sunday. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Down and Out for a Couple of Weeks --> but On the Mend
Started by Jason Edge in General Discussion. Last reply by Linda M. Brooks on Saturday. 2 Replies 0 Likes
I have been more than a bit quiet the past couple of weeks due to a really bad fall January 31 where I tore my right knee MCL ligament and ruptured the ACL Ligament. MCL will heal in time but ACL is…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
