Convertible Cylinder Bracket Removal

Hi, I'm hoping some of the other members here can chime in on this if they have experience with this. My convertible top motor burned out and while I was replacing it, I noticed the driver's side top cylinder was leaking. I ordered a new one and removed the current one and the bracket that attaches to it would not come off. It is held on with two philips head screws. One side came off with ease. The other completely stuck even after multiple shots of WD-40.  Is one of the sides reverse threaded? 

Views: 137

Facebook Facebook

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Chris Codd on July 31, 2014 at 8:16pm
Ok, so I was able to remove the bracket without removing both screws. One of the screws must be permanently fixed in place because it wouldn't budge. After removing the screw from one side (with absolute ease), I wedged the bracket in a c-clamp and a quick twist of the cylinder and it was out.

Photos

  • Add Photos
  • View All

Forum

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 14 hours ago. 11 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Steering slack/play

Started by Nile Bolen in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 4 Replies

I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack.  Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings,…Continue

Tags: box, play, steering

Add cruise control/Aftermarket Cruise control

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler yesterday. 12 Replies

Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue

Uniroyal Tire Brown Discoloration

Started by Sonny Butler in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Hi all,I'm glad I read Jason's recap of last nights Zoom call. I had the same problem with a set I bought for my 63 SDV. The white never got better than a pale yellow and would turn brown with in 5…Continue

Tags: Uniroyal

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service