Leather / Vinyl repair...found a really good company!

I wanted to share the following...my interior overall is not bad and does not to be replaced but needed some TLC. At a recent car show a vendor called Fibrenew made a nice presentation and said they would come to my home and started work to repair issues with my interior and to re-dye my leather back to original. The guy really took his time and made my backseat look like new. He will be back to finish the front seat. I'm amazed at what he was able to do to fix the cracking in the leather and how well he matched colors to make everything blend.

Views: 876


You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Kevin Williams on March 2, 2013 at 12:49am
Yes I'm very happy with the work performed. The company is fibrenew and I believe Jason posted their information on the parts supplier page. They are nation wide so you should be able to find a location near you.
Comment by Dave Schneider on February 28, 2013 at 9:11am
Kevin, can you tell the name of the company? Your interor look outstanding. Are you still happy with it? Thanks Dave
Comment by Kevin Williams on October 5, 2012 at 11:06am

Jason...they will give you an estimate and they stuck to it.  It cost me $450.00 and I'm estimating he spent every bit of 10+ hours working on the front and back.  They will come to your house and do all the work.  Best of all they stand behind their work you do not pay until your happy with the results.  I went this route because I just could not justify having the interior replaced when the fabric all still looked great, carpet is good, headliner is good it was just the leather that was the problem.

At this time I really don't need to do anything to the arm rests...while not perfect they still look very good.

Comment by David Thomas on October 5, 2012 at 10:03am

Amazing results......Looks great!!

Comment by Jason Edge on October 5, 2012 at 7:56am

Kevin, This is fantastic. What is the cost like on redoing the front and rear seats?  My original leather is actually not bad but do have a left arm rest top that is showing signs of wear. Are you having anything done to door panels or arm rest.   Again very curious about cost and how they charge...by the hr or by the job?

Comment by Kevin Williams on October 4, 2012 at 10:22pm

This company can do some amazing things with vinyl and leather that you would never think possible.

Comment by Chris Codd on October 4, 2012 at 10:09pm

Wow I wish I had met this guy before all the cracks in my seat turned to tears.

Comment by Kevin Williams on October 4, 2012 at 8:46pm

I wanted to follow up with everyone with some before and after photos.  All I can say is WOW...feel like I have new interior.

Comment by Jason Edge on September 28, 2012 at 8:39am

I posted a link to this message thread on our help page under Vinyl & Leather Repair and put a link to Fibrenew in our Parts Suppliers page.

Comment by Kevin Williams on September 27, 2012 at 10:35am

They are a national company with locations around the US and the World

Website is www.fibrenew.com

I will post before and after pictures once complete...the job has stalled due to wet conditions.  I took the car out last night to our local Cadillac Club Meeting and the members were impressed with how the back seat looked compared to the front seat.


  • Add Photos
  • View All


Dash Grille - Adhesive?

Started by Chris McBride in General Discussion. Last reply by Chris Codd 47 minutes ago. 2 Replies

This dash grille likes to vacation from the dashboard.  Is it properly secured with an adhesive and, if so, what adhesive?  If so, what type?  If not, how is it secured?Thank you.…Continue

Wiper Blades for a '63?

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 17 hours ago. 3 Replies

Is there anything special about the wiper blades I should use on my '63 Series 62 convertible? I have the original arms with the original blade brackets. I got Anco N-18R blades that should fit. I…Continue

Resistance wire removal or replacement

Started by Anders in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 19 hours ago. 38 Replies

Resistance wire removal or replacement.If installing an electronic ignition system the resistance wire most likely has to be removed or bypassed. There are several ways to do this and the solution…Continue

Tags: wire, resistance


Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 13 Replies

Has anyone had a bad alternator cause a weird misfire at idle, almost like the car is not sparking properly? I’ve upgraded to pertronix, replaced coil, plugs, plug wires and cap. Carburetor replaced…Continue

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…


1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…


New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …


Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…



  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service