Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob
Comment
I used mostly Gorilla Glue Spray Adhesive. I also used some 3M spray adhesive (I think #77) that I had half a can of. Both worked fine and gave me time to position and reposition fabrics while also being secure once dry.
Also, I reused the backing of the piece that comes down from the back shelf, but replaced the backing on the back (taillight end) of the trunk. For the replacement backing I used Neoprene Sponge Foam Rubber that I also got on Amazon. One 15" x 60" roll of this material was just the right amount.
I just redid my trunk. SMS Auto Fabrics sent me a sample of their fabric (about 1 1" square) and it looks essentially identical to the original fabric. I think the cost is $89/yard. It also seems to be directional (meaning it will look weird if the weave pattern is not oriented to make the weaves all go in the same direction) which will likely increase the amount of fabric needed. I don't really like the original material, and did not want to spend a lot the trunk, so I purchased my material on Amazon. I think it is similar to what OPGI sells (which is not a match to the original). The fabric I used can be found here for $60. I ordered one 4' x 20' piece that was just enough (it came as two 4' x 10' pieces). I was very happy with my choice.
You can see before, in progress, and after pictures of my trunk restoration....
Here is the end result before I put the jack and spare back in.
Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 2 hours ago. 1 Reply 0 Likes
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Started by Doug Scarrow in Wanted to Buy. Last reply by Dennis P. DiBari on Saturday. 3 Replies 0 Likes
for close to 20 years I have had a lovely Club Decal on my windshield now I wish to replace the windshield and would love to buy a decal if any one has one available See attached photosContinue
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe on Tuesday. 2 Replies 0 Likes
Is anyone here planning on going to the Back to the 50’s car show in Minnesota?
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge Jun 15. 2 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website