Is there anything special about the wiper blades I should use on my '63 Series 62 convertible? I have the original arms with the original blade brackets. I got Anco N-18R blades that should fit. I installed them on the arms. but they seemed loose, so I took apart the old blades and moved the rubber from the Anco blade to the metal spine in the prior blade. It's still not great. Given there don't seem to be any prior threads on this topic I suspect I am making tis wiper blade replacement harder than it should be.

Any suggestions for the replacement wiper blades that people use and that fit well?

Thanks,

Karl Schwarz
Centreville, VA

Facebook Facebook

Views: 253

Reply to This

Replies to This Discussion

Russ here on the forums has a stash of them. He should be able to help you out. 

I have new wiper blade refills for 20.00 a set plus shipping.  

email me at  russ@thecadishack.com    I will need your zip code for a shipping quote. 

I have been using and selling Anco U-18R refills for about 15 years and sell for $10 a set.  I have never used or sold the N-18R blades but the U-18R is s tight fit in the original blade holder.  I currently have about 8 sets. You may be able to find them for less but feel that is a fair price. If interested email me at jasonedge@nc.rr.com 

I believe the “N” refills were the narrow width refills, mainly for import cars in the 80’s back then.  The “U” refills were the standard American width at that time.

Karl, I have replied to your emails with no return reply. You asked for 2 sets of these in one email and I indicated 2 sets (4 blades) with shipping to US destinations would be $30. If not getting my emails check your spam folder. You can also message me here on the 63/64 site. I will assume you have what you need if no response. Jason.

RSS

Photos

  • Add Photos
  • View All

Forum

seat foam replacement

Started by Kevin Robles in 1963/64 Cadillac Specific Discussion 21 minutes ago. 0 Replies

does anyone out there have any experience with seat foam replacement on  a 63/64 Cadillac.  I had my seats reupolstered  many years ago in original leather/fabric and they still look great, but the…Continue

Timing cover corrosion

Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 6 hours ago. 1 Reply

Hey fellas if you're rebuilding your 429 check your timing cover for corrosion behind the water pump  Russ and I had 429 engine number two on the dyno today had shimed the oil pump spring for a…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Alan Clark 14 hours ago. 13 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Power steering fluid

Started by Bobby Brown in General Discussion. Last reply by Logan Robb 21 hours ago. 2 Replies

My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service