heater hose
I am replacing my heater hoses and was wondering if anyone has found a replacement for the 1479723. Its the 3/4" hose that goes from the heater core to the pipe running under the intake. Thanks
Replies to This Discussion
-
Permalink Reply by Larry Rees on
-
This is for a 64 Deville
-
-
I have tried to use a hunk of 3/4" off the roll but it starts to kink when bent in the small area. The hose that I removed was molded. It had the mold close enough to work but no part number left on it. The original part number 1479673 is no long any good but was looking for a conversion to a newer part number of a hose that is close enough to work without kinking.
-
-
Thanks good advice
-
Permalink Reply by Jason Edge on
-
Anyone have a good replacment # for Larry? I have replacement #'s for all the other hoses but would like to have a couple for this one. So, if you have a replacement # give us a shout. (Yes, I know we can all march to the auto store and have some one match one up, but we are looking for someone that has made that trek and id'ed a good replacement hose.)
-
Permalink Reply by David Thomas on
-
I us NAPA .75 inch 90 degree hose from the heater core to under manifold pipe. I think the part number is 9816. I trimmed the excess to fit. I use their 90 dgree .625 inch hose for the thermostat nipple to valve and from the valve to the heater core. Also trimmed to fit.
-
-
thanks
Members
Forum
where to find 1963 Cadillac Plastic Door Pin Anchors
Started by Frank Murch in 1963/64 Cadillac Specific Discussion 13 hours ago. 0 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Rear Main Seal Oil Leak Fix with Bearing Cap Modification
Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Matti Roth 17 hours ago. 15 Replies 4 Likes
Many owners have reported oil leaks at the rear main seal even after replacing the seal, myself included. Recently Tony Lentini found a Serviceman bulletin published in February 1965 which details a…Continue
Future of CLC Judging
Started by Jason Edge in Restoration Discussion. Last reply by Jason Edge on Thursday. 6 Replies 0 Likes
First, A Big Thank You to CLC Chief Judge Bill Anderson for taking on this daunting task of overhauling the CLC judging system. The old system was very good, however, I believe what Bill and the…Continue
front seat crest
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Frank Murch on Tuesday. 3 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
