Oil pump priming ,
Pulled the distributor and used a drill to prime the engine , Question, is oil suppose to shoot out of the gear shaft ? Been turning the gear clockwise p
Replies to This Discussion
-
Permalink Reply by Ray Schick on
-
Put the distributor back in ,set timing. Still seems to be a valve train noise ,shut it down .oil is up to level.filter is full of oil . Should I pack the gears with petroleum jelly ?and fill the oil filter neck with oil . Prior to this I had the front cover off changed the water pump,timing chain & gears. Should I pull the oil pump assembly apart and check the valve etc. Suggestions ?
-
Permalink Reply by Kurt on
-
If I remember correctly when I primed mine, I didn't see oil shooting out of the shaft gear but definitely felt resistance on the drill when the pump was primed and pumping oil. At 1st the drill will spin freely and when oil is pulled in you will feel resistance. Did that happen when you were priming the pump?
-
-
Not really Kurt.
-
-
Probably just need to perform the step below. After that, try priming with the drill again. If you feel resistance on the drill, you are good to go.
-
-
I’ll give it another shot
-
-
Thanks for everyone’s response, it seems like it’s solved ,took off the valve covers, and even pulled the oil pressure switch ran the drill for a good 10 minutes finally oil shot out of the switch port and oil is bleeding out of the rocker arms . Just waiting on some Bill Hirsh paint to paint and put it all together, paint is on BACKORDER … they said 4-6 weeks! that’s ok, We are at the end of our cruise season up in this part of the states.
Photos
Members
Forum
Burning Rubber
Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Linda M. Brooks yesterday. 5 Replies 1 Like
Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light? Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue
Gas gauge only reads half when full
Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin yesterday. 1 Reply 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
64 Brakes
Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply 0 Likes
Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue
Heater Core Replacement
Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson on Sunday. 6 Replies 0 Likes
I'm currently rounding up parts for a heater core replacement in my 1964 Deville. I'm looking for replacement hoses that connect to the heater core itself. It's a factory a/c car and has the metal…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
© 2026 Created by Jason Edge.
Powered by
