I recently brought in an original, unrestored 1963 Indiana license plate and posted on another thread and it was suggested we post pictures of our vintage, antique or personalized plates we run on our 1963/64 Cadillacs. 

I will start this off by showing a full rear shot of my 64 Coupe de Ville with an original 1964 North Carolina license plate.  In NC you can run a correct vintage plate as long as you keep the current license plate and registration in the car. Unlike some states they are not linked.  My plate is like new and believe it was restored.  I bought it so long ago now I can't remember!

If you have a unique plate on your 63/64 Caddy please share! Maybe we will run these in a future newsletter. 

Views: 362

Reply to This

Replies to This Discussion

Here's my 64 NY Plate

 Very cool plate.  Neat to see the NY World’s Fair promoted.

Very nice Fleetwood! I don't see many of those on the page. Nice and bright taillights too! I need to do some work on mine to brighten them up. Clean ground and some fresh bulbs are in order...

Oh, and nice plate!

Thanks! I replaced the lenses with repros and also sprayed the inside of the housings with chrome spray paint in addition to cleaning up the sockets. Seemed to help a lot.

That can help a lot. I did a batch of the 63 tail lamps last year and will do a batch of 64's at some point later this year! Here is a before and after with the 63 tail lamp.

How important is the gasket that is in that housing? My gasket are present, but not in good shape by any means. I have been wanting to spray my TL lenses as the photo above, but I dont want the gasket to crumble as I know it will!

Are there repops that I can use?

Here is the correct year CA plate currently on my de Ville. It is not the original plate of the car.  The Texas plate below was from my first de Ville that I had in the 1980s.

RSS

Photos

  • Add Photos
  • View All

Forum

Burning Rubber

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 1 hour ago. 7 Replies

Out of curiosity,, is the 63 64 engine capable of burning rubber off of a stop light?   Not a hold the brake and rev up and release, but from a stop, to burn rubber power?I know mine wont because i…Continue

Gas gauge only reads half when full

Started by Kenneth Barton in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Wednesday. 1 Reply

Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue

64 Brakes

Started by Jeff Donaldson in General Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply

Hi,It's time to do a brake job on my Fleetwood. When I imported my car from the US to Canada I had to have my car safety inspected before I could license it in the Privince of BC. After the…Continue

Heater Core Replacement

Started by Michael Monson in 1963/64 Cadillac Specific Discussion. Last reply by Michael Monson Feb 15. 6 Replies

I'm currently rounding up parts for a heater core replacement in my 1964 Deville.  I'm looking for replacement hoses that connect to the heater core itself.  It's a factory a/c car and has the metal…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Videos

  • Add Videos
  • View All

© 2026   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service