I recently purchased a 1963 Coupe deVille. The transmission will only shift 1st to 3rd. I put the car on a lift and drained the pan and torus. I removed the shift valve body and coupling valve body, cleaned the pistons and bores, replaced the filter and fluid and adjusted the TV rod per spec. No change in the way it shifts. I have read that the aluminum cover on the fluid coupling is prone to cracking which will also cause the trouble I am having. I feel a rebuild is is in my future. Other than Gene's transmission in California, can anyone recommend a shop on the east coast? I live in Virginia Beach, VA. John. 

Views: 270

Reply to This

Replies to This Discussion

Hey John , go to the Cadillac / Lasalle  Club site and post your question . Im sure somebody can help you find a Trans guy by your area, Good Luck. Ray 

John, did you happen to find any other shops or what was wrong? My transmission is doing the same.

I called Gene and talked to him for an hour. He is near genius but just a little more than I wanted to pay.

Josh, I live in Virginia Beach Virginia and finally found a shop in my area to overhaul my transmission The shop is CarLife Transmissions in Norfolk Virginia. The owners name is Fred Kent and he is very knowledgeable. Before I could tell him what steps I had taken to correct the problem he told me exactly what was wrong. I had already researched the problem and knew that the secondary fluid coupling was leaking. The only way to correct it is to pull the tranny. I dropped off my car at the shop 2 weeks ago and and am expecting it back any day now. He quoted me $3980 (must be the going rate for a Jetaway) for the overhaul and had every part needed for the rebuild. That price included removal and installation. Yes, I know it is quite a bit but at least I know it will be done right.

Thanks for the info John. BTW, I love VA Beach...I was stationed at Langley AFB for 4 years. That's my old stomping ground!!

RSS

Photos

  • Add Photos
  • View All

Forum

Cadmium Plated Front and Rear Bumper End Fastener Sets

Started by Jason Edge in For Sale 1 hour ago. 0 Replies

I will start grouping some of my fastener sets and thought I would start with the bumper fasteners. These have links that point to photo albums on my Facebook Parts Page at…Continue

Windshield washer pump inoperative

Started by Wayne Morris in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Saturday. 14 Replies

I have spent a few hours trying to get pump to pump fluid. The lines are all clear, The pump Is working as it should when the washer button is pushed. I have a spare wiper motor assembly which I have…Continue

63 vs 64 Hood V Size Difference

Started by Jason Edge in 1963/64 Cadillac Specific Discussion on Saturday. 0 Replies

The 64 hood V is considerably bigger than the 63 hood V, and one of the many things I have not done in dealing with these cars on the last 3 decades was to do a direct comparison. Someone asked about…Continue

Radio Models 1963 to 1968

Started by Jason Edge in 1963/64 Cadillac Specific Discussion on Friday. 0 Replies

I sometimes get asked what radios were used in 1963 and 1964 or verification of a radio model number, so I scanned the radio listing from a 1968 Master Parts Book that covers 63 to 68 which covers…Continue

Blog Posts

'63 Tailfin Tales

Posted by Mark Mata on January 14, 2025 at 12:06am 0 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service