After changing tie rods, i tokk car into wheel n allignment shop. He said no problem.  He calls back about 45 minutes later and said they couldnt get between the tire and cowl, the guys head was too big!!  I said. Your kidding!  He said no.  You can pick up when you ready.  I asked if he could suggest another shop, he said not really, but wherever to go, try to find smaller alignment guy

Hv you ever heard such a thing?  Im not making this up guys!

Views: 81

Reply to This

Replies to This Discussion

Sure this is BS 

He did not want to do the job for some reason but that’s one hell of an excuse   LOL !

Enjoy 

I called another company, they said there software does go back to 63

Kim 

Bring your service manual to the shop so they have the  stock specs for your car 

Those specs WB for bias ply tires 

The specs for radial ply tires are a bit different 

Enjoy 

Disregard my  post above this 

Thx 

Kim 

Go to the Help page under - Alignment —- and you will see the specs for either Bias ply tires or Radial tires depending what you use 

Give them to the wheel alignment numbers for the tires you are using 

That should help them get it done right 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Radio restoration

Started by Joe DiIaconi in 1963/64 Cadillac Specific Discussion 1 hour ago. 0 Replies

I had my 1964 radio restored a few years ago and now it's not working correctly. Can anyone recommend a reputable place to have it restored again?Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 10 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Grandpa’s Cadillac Restoration

Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 21 hours ago. 13 Replies

Hello friends! It’s been a while since I’ve visited this page. Last I left I had spoke about my late grandpa’s Cadillac that I planned on “restoring”, which really meant getting back on the road.…Continue

Crankshaft - ‘64 Sedan Deville

Started by Jordan Johansen-Moe in Wanted to Buy. Last reply by Jason Edge yesterday. 1 Reply

Hello friends! I’m looking for a crankshaft for a 429 that will begin Grandpa’s Cadillac Restoration. I will be talking to a machine shop on Monday (fingers crossed). However, in the event I hear the…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 5 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service