Hello,

Just wondering if anyone has photos to where I need to apply new SEM seam sealer on the front of the fenders to the inner top Cowl area and the corners of the Radiator support?

I am in the process of reinstalling new painted cowls and radiator support.

I know it had factory new but did not take photos of that area.my memory is not that good from two years back.

Thank you

Don

Facebook Facebook

Views: 49

Reply to This

Replies to This Discussion

I have ZERO experience with seam sealer locations on this vehicle nor really any other vehicle. HOWEVER, I did grinde, sand, wire brush, fabricate and stitch in new floor pans and the whole interior floor on a 77 Lincoln Town Car. I put seam sealer on anything that remotely looked like a seam. I used tubes in a caulk gun as well as a 1 qt can. I used a brush and brushed over the seam first pushing the sealer as far in as I could. Then I ran a bead like it was a bead of silicone or a welding bead. Then I made it look as best I could. I think maybe the applied area was 2" wide when I was done. Followed by a coat of paint, I think it was better than what would have been quickly sprayed on by gun at the factory. 

Now, this area was going to be covered by butyl sheets and then isolation foam sheets, and then jute and carpet. So for someone to see it again, they'd be trying really hard. 

The area you are asking about seems a little more visible. In that case, I may use some painters tape and tape off the area you are working for more of a finished look. Otherwise, good luck!

Logan

Thank you For your message Logan

RSS

Photos

  • Add Photos
  • View All

Forum

The $120,000 1963 Eldorado on Bring a Trailer

Started by Jason Edge in General Discussion. Last reply by Kurt 5 hours ago. 6 Replies

I have got a flood of email, texts, about the 63 Eldo that recently bid up to $120,000 and thought I would share for those that have not seen it.Here is the link:…Continue

Fuel Supply System - Check Points Beyond the Fuel Pump

Started by Jason Edge in General Discussion 7 hours ago. 0 Replies

Incredibly, in 3 days I have had 3 people ask about replacing their fuel pump or even adding an electric fuel pump because there carb is not getting gas.  It has gotten to the point I have copied and…Continue

Tags: System, Delivery, Fuel

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 13 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Houston we have a problem!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Monday. 3 Replies

While enjoying the fruits of my labor on all new rear suspension and…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service