"Hi Joel, how sure are you of the condition of the fuel pump?
I had a pump go out on me and I thought I was fighting vapor lock."
Kenneth Barton's Discussions
No dash lights, headlights only come on with dimmer
Started this discussion. Last reply by Kenneth Barton Mar 22. 6 Replies 0 Likes
I’m in the midst of refreshing some things in my dash. I got my passenger ash tray working for the first time ever apparently, evident by the factory defect tag. “While I’m in here I might as well…Continue
Fuel gauge needle bouncing
Started this discussion. Last reply by Dennis P. DiBari Mar 20. 3 Replies 0 Likes
Hi everyone,I'm in the midst of diagnosing two fuel gauge problems. Originally it would only read half full after filling up.After replacing it with a recalibrated gauge, now the needle bounces like…Continue
Gas gauge only reads half when full
Started this discussion. Last reply by Russ Austin Feb 18. 1 Reply 0 Likes
Hi everyone, I installed a new gas tank sender in my 63 after bench testing it and confirming ohm range on the bench.However after installing and filling it up, it only reads half full after filling…Continue
63 passenger ashtray won’t release
Started this discussion. Last reply by Kenneth Barton Nov 19, 2025. 6 Replies 0 Likes
Hi everyone,I’ve been working on freeing up the passenger side ashtray on my 63. You can push the ashtray in all over the unit and it won’t release. The only way to get it to flip down is to push the…Continue
Kenneth Barton's Page
Latest Activity
"Think I found the culprit - looks like a broken connection on the rheostat.
Studying the thing for a little bit lead me to this."
"So it seems that the gray wire is not getting power at the headlight switch, despite power being fed properly.
Everything looks good on the outside of the switch, but I’m going to attempt disassembly."
"Touching both sides of the fuse with my meter yields 12.2v.
I’m afraid somehow there’s a breakage in the wires in between."
"Thank you both gents. I had the connector installed incorrectly - it was one blade too far over. Now headlights work as expected.
Still diagnosing dash lights. The single gray wire is getting 0.34v. The red, blue and green wires on the headlight…"
"Troubleshooting is in order. The single gray wire on the headlight switch is the dash lights. The blue wire on the connector is the headlight power to the dimmer switch. Check that they have 12V"
"That is strange. Did you replace with incandescent bulbs or LEDs? I've heard that some LEDs are not the correct polarity for these cars. Did the headlights work fine before you cleaned the switch? If you disassembled it, maybe something went…"
No dash lights, headlights only come on with dimmer
I’m in the midst of refreshing some things in my dash. I got my passenger ash tray working for the first time ever apparently, evident by the factory defect tag. “While I’m in here I might as well replace some bulbs proactively.” That was a mistake. After replacing bulbs, nothing worked. I decided to clean the headlight switch - all the contacts with alcohol and a q tip.Now I have no dash lights at all, and the headlights come on only when you rotate the dimmer all the way like you’re…See More
"Hi Ken,
Very glad that it worked for you. That is usually the culprit - good work on your part that you fixed it!
Dennis DiBari"
"I was so confident that wasn’t it…until I looked closer and realized the screw wasn’t holding the ground tight to the metal. I switched to a traditional nut and bolt and bam! Rock steady.
Thanks Dennis!"
"Hi Ken,
How about the ground wire off the gauge, that runs to the rear of the car with a bolt on the rear frame. It is near/under the license plater cover. Make sure it is cleaned and tight. Take a look at…"
Fuel gauge needle bouncing
Hi everyone,I'm in the midst of diagnosing two fuel gauge problems. Originally it would only read half full after filling up.After replacing it with a recalibrated gauge, now the needle bounces like crazy all over the place when the car is moving.I'm assuming there's some sort of chafed ground somewhere - the tank and sender are brand new, sender was bench-tested. The fuel gauge is also recalibrated.Any ideas on places to look very closely?Thanks!See More
"The gauge is out of calibration. I have gas gauges that I had calibrated at an electrical shop for 125.00
email me at russ@thecadishack.com if interested."
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 63 Coupe
- Cadillac LaSalle Club Membership Number? (Must be a member to Join Chapter & Website)
- 35691
- 1963/64 Cadillac Chapter Member?
- Yes
Comment Wall
- No comments yet!
Photos
Members
Forum
WTB: 1963 Double Cardan CV Ball Socket Repair Kit (NEAPCO 2-9303)
Started by Mark Geertsma in Wanted to Buy. Last reply by Ian Arnold on Sunday. 5 Replies 0 Likes
Looking to buy the -now seemingly obsolete (?)- NEAPCO 2-9303 double cardan CV joint repair kit for my 63 SdV.Anyone here who has one for sale or knows about an equivalent?Continue
WTB console lid deck for 63 Eldorado
Started by Cees de Bunje in Wanted to Buy. Last reply by Russ Austin on Saturday. 1 Reply 0 Likes
Hi guys, I am looking for a deck lid of the console between the bucketseats of a 63 eldorado biarritz. I only need the deck. Especially the chrome part that is fitted on the inside or the underside…Continue
Letter E for Fender E L D O R A D O sign on 1964 Eldorado
Started by Remco Waller in 1963/64 Cadillac Specific Discussion on Friday. 0 Replies 0 Likes
Hi,I unfortunately lost the letter E on the left front fender of my 1964 Eldorado.I did see on both E-Bay and McVey's that I could buy full replacement sets but does somebody has and wants to sell…Continue
ENGINE BAY CADMIUM PLATED PARTS LIST
Started by Jason Edge in For Sale Jul 6. 0 Replies 0 Likes
ENGINE BAY CADMIUM PLATED PARTS LIST:…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
New old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Events
-
July 26, 2026 - 63/64 Cadillac Chapter Zoom Meet-Up
July 26, 2026 from 8pm to 9:30pm – Zoom
1 Comment 1 Like
Videos
© 2026 Created by Jason Edge.
Powered by
