"On one side, I don’t have the holes since it’s a replacement fender from a non-fleetwood. So I ground off the pegs and just put glue on the backside of the letter. On the other side, I have the pegs so I used a little on the back of the…"
-
Michael Buonaccorso
- Male
- Rochester, NY
- United States
- Blog Posts
- Discussions (29)
- Events
- Photos
- Photo Albums
- Videos
Michael Buonaccorso's Discussions
B Pillar Interior Trim
Started this discussion. Last reply by Jason Edge May 3. 2 Replies 0 Likes
Hi Everyone:The interior trim covering for my B Pillars is missing in my 64 Fleetwood, and I am wondering what the piece(s) looks like so I can recreate it.I found this photo online (not a Fleetwood)…Continue
Rear Vent Window Weatherstripping Replacement
Started this discussion. Last reply by Michael Buonaccorso Dec 25, 2022. 7 Replies 0 Likes
Has anyone here replaced the weatherstripping on the rear vent windows of a Fleetwood 60 Special? Unlike the front vent windows, the pivot shaft of the window is inserted into the weatherstipping…Continue
Fleetwood vs. other 6 window sedans
Started this discussion. Last reply by Michael Buonaccorso Apr 25, 2022. 9 Replies 0 Likes
Are the rear doors on other 6 window sedans the same as the Fleetwood 60 special? Obviously the door cards are different, but is that it? Steele has weatherstripping available for the rear door 6…Continue
Rear patch panel
Started this discussion. Last reply by Tony and Ginny 429 Sep 7, 2021. 3 Replies 0 Likes
I am looking for a patch panel to weld in to replace the rusted out section of my rear end as circled in the picture. This is for a 1964 Fleetwood 60.Regards,MikeContinue
Michael Buonaccorso's Page
Latest Activity
"I used superglue, and once it set up it was an extremely strong hold. Just be careful and don’t use too much. I first tried using 3m plastic trim adhesive, but it didn’t work well and a letter fell off (luckly in my driveway)."
"I sent MIke an email this morning with pictures but thought I would share here showing the front and back of these. I was able to locate several colors in my stash but not the sandalwood with the cut pile that he needs. The only difference…"
"There is not cardboard on the back... it is just a piece of carpet on the bottom sewn to a piece of vinyl/leather at the top, and glued to the metal inside B-pillar with what looks like that 3M spray adhesive. From memory there is not difference…"
B Pillar Interior Trim
Hi Everyone:The interior trim covering for my B Pillars is missing in my 64 Fleetwood, and I am wondering what the piece(s) looks like so I can recreate it.I found this photo online (not a Fleetwood) - It looks like there is carpet on the bottom, and then maybe matching leather (?) above that. Is there a cardboard backer that ties it all together or are they separately attached? Also, does it vary based on model?…See More
"FYI for future reference, the 61-63 seals do work fine on the 64. I'll take some pictures and post them in a few days so others have a reference.
Thanks Russ for your help!"
"Thanks Jason, good suggestions. Steele lists the replacement part for Fleetwoods from 61-64, so that broadens the search even more."
"Michael, as a CLC member I would reach out to other members with a 63/64 Fleetwood and see if they have run into this rear vent window rubber seal issue. Marty Smith is one member that I know has restored a lot of his Fleetwood 60 Special. Looking…"
"If all else fails you might try to use the old part of the weather strip with the metal insert ( if salvageable ) and attach the new weatherstrip rubber to it using a CA glue ( crazy glue ) that is excellent for bonding rubber to rubber for…"
"If the weatherstrip is not correct I would think another source might be the answer for the correct part
You might try - Restorers Choice - to see if they might have what you need
Just a best chance guess on my part —-but…"
"The issue is the metal is molded into the weatherstripping itself. On the new piece there is also a metal strip molded in, but the area where I could potentially drill a hole is notched out and is only rubber. "
"Michael. One would assume since the metal guide piece didn't come with the rubber you were to reuse the old metal I am seeing in the picture. I have some 60S rears somewhere and can take a look at one when it gets above 10 degrees, but…"
"See photos"
Rear Vent Window Weatherstripping Replacement
Has anyone here replaced the weatherstripping on the rear vent windows of a Fleetwood 60 Special? Unlike the front vent windows, the pivot shaft of the window is inserted into the weatherstipping itself. On the original rubber, there was a hole in the molded steel of the weatherstripping that it fit into. On the reproduction (Steele), there is just a rubber pocket with no metal backing, so a hole (with integrity) can't be drilled. As a result, I cant properly keep the window from falling out. I…See More
"Russ
That was me! Good find, all though my specific needs are for a 64. Still on the hunt, but I have some ideas…"
"Thanks for the idea!"
Profile Information
- Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
- 1964 Fleetwood 60 Special
- Cadillac LaSalle Club Member? If Yes, Membership #?
- 32717
- 1963/64 Cadillac Chapter Member?
- Yes
Comment Wall (1 comment)
- At 8:02am on June 16, 2020,
Jason Edge said…
Welcome to the 63/64 Cadillac Website.
This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the Chapter.
- Click on www.join.6364cadillac.com for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club.Be sure and check out all the links and pages and make yourself at home. The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.
Photos
Members
Forum
KleerView/OptiKleen Bottle Location
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb 6 hours ago. 3 Replies 0 Likes
I just received a repop KleerView bottle and label for my 64 Fleetwood this morning. Wondering where the best location for this bottle would be? Or rather, where was it most commonly installed?I…Continue
Current 1963/64 Cadillac Listings on eBay
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 20 hours ago. 1 Reply 5 Likes
To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue
Tags: ebay
1964 A/C Delco Parts book for Deville
Started by Mark Bartlett in General Discussion. Last reply by Jason Edge yesterday. 1 Reply 0 Likes
Is there a place to go to buy or look at original parts book ThanksssContinue
differential seal
Started by Al zink in 1963/64 Cadillac Specific Discussion. Last reply by Al zink on Monday. 2 Replies 0 Likes
Can anyone provide me with a good source for a differential seal for my 63 cadillacThanksContinue
Blog Posts
Lower Front End Ball Joints
Posted by Logan Robb on May 11, 2023 at 9:04am 7 Comments 0 Likes
Good Morning all!
I took the 64 into the shop to have some adjustments completed and in the process decided to have the lower ball joints replaced as was recommended the last time I had it in. I ordered the parts and came into the shop. They quoted me nearly $500 to replace those lower ball joints requiring nearly 4hrs of labor. Now this is a reputable shop and they know me by name here and they will continue to get my business. I am just questioning what on earth is…
Continue1964 power steering sector rebuild
Posted by CHRIS CARLSON on March 20, 2023 at 11:32pm 3 Comments 0 Likes
I'm having my steering sector rebuilt, and considering changing it from 20-1 ratio 4.2 turns lock to lock to 3.5 turns lock to lock @ 16-1 ratio, If i change from a 3 1/4" box to a 3" box i could have a 14-1 Ratio steering response would be faster, shorter distance to turn the wheel to get a response, has anyone done this? and how do you like it? thank you
1964 Daville dashboard clock
Posted by Willem Bol on March 13, 2023 at 11:33am 2 Comments 0 Likes
Hallo,
Can somebody help me finding a dashboard clock for my 1964 Cadillac DeVille Convertible?
Thank you in advance,
Willem Bol
The Netherlands
Does anyone know where I can get the bushings for AC compressor mount on the 429?
Posted by Robert Schles on February 21, 2023 at 11:45am 2 Comments 0 Likes
I've looked at the usual rubber sources but couldn't find any.
Events
© 2023 Created by Jason Edge.
Powered by
