GASP! Yes, I know tires get talked about ALL the time. So here we go again. 

235/75/R15 seem to be the standard replacement for the 8.2x15 bias ply. 

I ~REALLY~ want to put bias ply on my 64 Fleetwood, however, I think my front end needs a decent overhaul before that happens. I need tires before I’ll be able to overhaul the front end. SO. That being said, I’m looking for the best looking white wall radials for a decent price I can find. 

Close to the factory white wall spec, but if it’s a little wider, I won’t complain. Nothing too wide tho. 

Thanks all! 

Logan 

Facebook Facebook

Views: 129

Reply to This

Replies to This Discussion

Robb, I dont know what you are willing to spend, but i purchased Diamond Back Classics  8.25 x 15 Radials with a 1 inch whitewall and the pie crust edge @ the tread on the sidewall . I told them my original spare tire had a one inch white wall so they made it for me. The tire is the AUBURN DELUXE they where $1100.00 for four. Heck now days you spend that much putting tires on a half ton Chevy pickup.

How about some pics? Love to see that! That’s a reasonable price I think. $275 per. Not bad.  

It’s getting harder to find white walls at any price.  I bought four Cooper Trendsetters at a local Discount Tire several years ago at about $80 each (can’t remember if that was before or after the excise tax, disposal fee, warranty and other “add on s”).  

Another member posted a pic of this type of tire at:

https://6364cadillac.ning.com/profiles/blog/show?id=6543066%3ABlogP...

Here’s another

hth

Attachments:
Attachments:

Oh those look really nice! Thank you! 

Personally Id go with the BF Goodrich L78x15 dual white wall tires that Coker sells. The width is more like 8.85 and according to research these were strictly a Cadillac tire. They retail for 330 a tire. I know I certainly plan on getting a set as I think it'll look much better than the nubby Yokohama tires that are on the gal now.

RSS

Photos

  • Add Photos
  • View All

Forum

Carburetor

Started by John Inglesby in 1963/64 Cadillac Specific Discussion 9 hours ago. 0 Replies

Any suggestions on carburetor rebuild for my 64 DeVille convertible. I guess it's a Carter or Rochester?Continue

Dino Diaries - Feb 25, 2025 - Open Up and Say Ahh!

Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply

Just back with a new batch of cadmium plated parts, I like to imagine Dino saying "Ahh" as I sort through the next cad plated goodies to install. This morning I installed a cad plated fuel pump to…Continue

Pick Up of 11th Batch & Drop Off of 12th Batch For Cadmium Plating

Started by Jason Edge in General Discussion on Monday. 0 Replies

As I shared last night in our Chapter Zoom meeting, here is a picture of the 9 totes with fasteners and other parts that will be taken to Winston-Salem NC for cadmium plating. This will be my 12…Continue

Which Shocks for my 64 SDV are MOST like Originals?

Started by Norman Silverman in 1963/64 Cadillac Specific Discussion. Last reply by Norman Silverman on Monday. 4 Replies

I am considering replacing the shocks in my 64 SDV. They're not terrible, but are a little too wishy-washy. I want to replace them with shocks that most closely approximate the original damping rate…Continue

Blog Posts

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 5 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service