front seat crest
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?
Replies to This Discussion
-
Permalink Reply by Kurt on
-
SMS Auto Fabric did mine (smsautofabrics.com). The product quality is excellent BUT it will take FOREVER to get your order so be prepared to wait if you order from them. If you already have your leather & just need a section embossed, they might do that for you. I bought leather, vinyl, & fabric from them 20 years ago to reupholster my car. My upholsterer cut sections to do the rear seat & the center arm rest and marked them on the underside for where to emboss them. I sent those sections back to SMS for embossing. I think the turnaround time for the embossing was not too bad. The end result was beautiful seats but it was quite a wait.
-
Permalink Reply by Bill Wolf on
-
Kurt, your seats look great, and the crest just adds the next level of style. Can't wait until I get to the point of upholstery upgrades. Nice job
-
Permalink Reply by Frank Murch on
-
thank you!! ses they did my door panels during covid. It was 2-3 years?
Members
Forum
Power steering fluid
Started by Bobby Brown in General Discussion. Last reply by Dennis P. DiBari 5 hours ago. 1 Reply 0 Likes
My reservoir is a little low. Any recommendations on my purchase of refill fluid? There are likely new fluids and I’d like to buy the right product. Thanks. Continue
Dino Diaries - July 11, 2025 - Busted!
Started by Jason Edge in General Discussion. Last reply by Jason Edge yesterday. 4 Replies 0 Likes
So I am starting to crawl around under Dino seeing what I can fix or upgrade and as I was putting the trans linkage in a few nights ago, the rear trans mount caught my eye. I remembered that these 64…Continue
Bleeding brakes
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Thursday. 3 Replies 0 Likes
I have finished replacing all the rear suspension and am at the last item, which is bleeding the rear brakes. I am using the Jason Edge vacuum pump method and all went well with the rear passenger…Continue
Front grill
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Wednesday. 8 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
-
July 20, 2024 - 63/64 Cadillac Chapter Zoom Meet-Up
July 20, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
Videos
© 2025 Created by Jason Edge.
Powered by
