Dave Schneider's Discussions (152)

Discussions Replied To (124) Replies Latest Activity

"I put a top on a 57 Chevrolet when I was 18. It worked well. "

Dave Schneider replied Apr 6 to Anyone attempt to replace convertible top yourself?

3 Apr 6
Reply by Dave Schneider

"Karps Brakes in Upland, Ca did both of my cars. 909 985-0800"

Dave Schneider replied Feb 11 to Recommended rebuilder for 63 Convertible's brake booster?

6 Feb 11
Reply by Ben Roberts

"I found time to flip the calipers around today. They are marked right and left.  I h…"

Dave Schneider replied Feb 7 to What years of booster will bolt on without making bigger holes?

6 Feb 7
Reply by Ian Osborne

"Thanks to all! I think I found my problem.  The bleed valves on the calipers are at…"

Dave Schneider replied Feb 5 to What years of booster will bolt on without making bigger holes?

6 Feb 7
Reply by Ian Osborne

"Thanks Tony!  Yes it was dumb!  But done. I want to stick with a GM booster.  I purc…"

Dave Schneider replied Feb 3 to What years of booster will bolt on without making bigger holes?

6 Feb 7
Reply by Ian Osborne

"Thanks All!! I am going to take it to a outstanding shop with old guys at the helm!…"

Dave Schneider replied Feb 2 to How to adjust strut rod.

8 Feb 2
Reply by Dave Schneider

"Thanks for taking the time to help answer my question!  Good point on radial tires w…"

Dave Schneider replied Feb 2 to How to adjust strut rod.

8 Feb 2
Reply by Dave Schneider

"I used ABS disk brake kit with Kelsey Hayes 40 spokes wires. "

Dave Schneider replied Sep 30, 2019 to Disc Brakes and Cadillac 48 spoke wire wheels

4 Feb 23
Reply by Dan Loukota

"I used ABS disk brake kit with Kelsey Hayes 40 spokes wires. "

Dave Schneider replied Sep 28, 2019 to Disc Brakes and Cadillac 48 spoke wire wheels

4 Feb 23
Reply by Dan Loukota

"I am having problems with my front disk brake dragging.  The temperature is 130 with…"

Dave Schneider replied Aug 2, 2019 to Disc brake conversion kit

29 Aug 2, 2019
Reply by Tony and Ginny 429

RSS

Photos

  • Add Photos
  • View All

Forum

Bendix Power Brake Unit Power Section

Started by Mathis Richter in 1963/64 Cadillac Specific Discussion. Last reply by Chris Codd yesterday. 7 Replies

Hi,I have a huge problem my POWER SECTION of the ``Master-VAC Power Brake unit 9´´Diameter ´´ from Bendix is Broken and I can't open it to replace al the rubber parts did some of you have auch Power…Continue

Third brake light -help please.

Started by paul k in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 8 Replies

Did anybody from the club install third brake light in the rear window in his Cadillac? I have problem to figure out how to do it. Can I just run wire from break pedal switch and second wire connect…Continue

Extra speakers in the cadillac.

Started by paul k in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

Ok, I have another question. Since I will run wire for a brake light I might run speakers wires.I would like to install 2 extra speakers or maybe 4. What is best option. I do have 2 speakers already-…Continue

429 and 400 trans. for sale

Started by Mark C Bills in For Sale. Last reply by Tony and Ginny 429 on Monday. 6 Replies

I have an excellent running 429 with 400 trans.recently removed from my 64. It has electronic ignition, new water pump,new fan and clutch(not pictured),new fuel pump,Holley 650 vac. sec. carb. with…Continue

Blog Posts

1964 Cadillac Fleetwood sixty special / transmission dipstick needed

Posted by Pablo on September 20, 2020 at 9:57pm 1 Comment

How are you doing folks, I’m looking for a transmission dipstick, any info I will appreciated, thank you very much

1963 Cadillac hood driver side hinge

Posted by Steven on September 16, 2020 at 9:23am 1 Comment

Hello,

 Does anyone know were I can buy a 1963 Cadillac hood driver side hinge or is there any other hinge that would fit? 

Thanks

Steven

Bad Guage?

Posted by Karl Schwarz on August 26, 2020 at 3:08pm 6 Comments

So I am troubleshooting my fuel gauge issue. I bought a new sender and tested it. It  it goes from 1-ohm (empty) to 35-ohm (full). When I test it (outside the tank), when the float is in the up (full) position it only moves the gauge to about 1/2 full. When at the bottom (empty) position the gauge shows empty. This is the same issue I have when I fill and then use the gas in the tank - the gauge never reads ore than half full. Based on what I've read on this thread it would seem like the…

Continue

Website

Posted by Fritz Seitz on August 11, 2020 at 2:35am 0 Comments

I have been working on a website-----www.fritzsautorepair.com-----

Does anyone have suggestions?

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service