Phil's Discussions (24)

Discussions Replied To (19) Replies Latest Activity

"Try oiling the rockers  by hand to see if the noise goes away. "

Phil replied Aug 8 to Noise in engine

24 Aug 8
Reply by Jason Edge

"What is the temperature rating on your thermostat? If it’s lower like a 160 degree y…"

Phil replied Jul 31 to Over heating

9 Jul 31
Reply by Tony and Ginny 429

"Maybe a stupid question but,  does your mechanic understand the he needs to turn the…"

Phil replied Jun 23 to 63 coupedebille fuel pump issues

20 Jun 23
Reply by Tony and Ginny 429

"You can get a rebuild kit for the original pump,  it’s a pretty straightforward task…"

Phil replied Jun 17 to 63 coupedebille fuel pump issues

20 Jun 23
Reply by Tony and Ginny 429

"Yeah,  That pushrod is very sensitive to adjustment , I ended up just tightening and…"

Phil replied Jun 15 to Very sensitive brakes.

19 Jun 16
Reply by Tony and Ginny 429

"After driving the car around town,  The brakes seem to have settled in and are worki…"

Phil replied Jun 14 to Very sensitive brakes.

19 Jun 16
Reply by Tony and Ginny 429

"An update on this,  I took Tony’s advice on the spring spacers,  and the car Sits, r…"

Phil replied Jun 6 to Body mounts and loose feeling rear end.

9 Jun 6
Reply by Phil

"We’ll see how they go,  I’ll keep you updated.  I agree with you on the veggie hambu…"

Phil replied Jun 6 to Very sensitive brakes.

19 Jun 16
Reply by Tony and Ginny 429

"Thanks Tony.   Element 3 organic is what Raybestos is branding their shoes and pads…"

Phil replied Jun 5 to Very sensitive brakes.

19 Jun 16
Reply by Tony and Ginny 429

"Thanks Mark,  I wish that was the issue,  I’ve checked that a few times. "

Phil replied Jun 5 to Very sensitive brakes.

19 Jun 16
Reply by Tony and Ginny 429

RSS

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 30 minutes ago. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Dash Grille - Adhesive?

Started by Chris McBride in General Discussion. Last reply by Chris Codd 1 hour ago. 2 Replies

This dash grille likes to vacation from the dashboard.  Is it properly secured with an adhesive and, if so, what adhesive?  If so, what type?  If not, how is it secured?Thank you.…Continue

Wiper Blades for a '63?

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 18 hours ago. 3 Replies

Is there anything special about the wiper blades I should use on my '63 Series 62 convertible? I have the original arms with the original blade brackets. I got Anco N-18R blades that should fit. I…Continue

Resistance wire removal or replacement

Started by Anders in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 20 hours ago. 38 Replies

Resistance wire removal or replacement.If installing an electronic ignition system the resistance wire most likely has to be removed or bypassed. There are several ways to do this and the solution…Continue

Tags: wire, resistance

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service